Extraordinary designer waterfall made of chlorine and salt water resistant stainless steel for swimming pools and garden ponds. Including accessories for connecting to
existing pool fi lter systems and garden pond pump. The model
MAMBA
LED/BIRDIE LED with integrated LED-lighting (12V).
Technical data
Model
Waterfall
MAMBA
WATERFALL
MAMBA
LED/BIRDIE LED
Article number EU
7504442
7504459 / 7504666
Material
INOX 316 L
INOX 316 L
Hose connection
1 1/2” (female thread)
Recommended pump capacity
Pools with sand fi lter
(0.8 bar = 8 m delivery head)
5.5 – 11.3/h
5.5 – 11.3/h
Poolmax TP 75 / 120
Poolmax TP 75 / 120
Garden ponds
6,000-12,000 l/h
6,000-12,000 l/h
Cascademax 12000
Cascademax 12000
LED-lighting
LED-strip
30 cm, 20 LED, blue / 30 cm, 20 LED, cool white
Voltage/frequency
12 VAC 50 Hz
Safety transformer
TDC 3.25-12 W
Power consumption
2.5 W
Cable length LED-lighting
5 m
Class of protection
III
Protective system
IP68
Delivery volume
Tee-piece connector 1 1/2 “
1
1
Ball valve 1 1/2”
1
1
Hose nipple 1 1/2” x 38 mm
4
4
Hose clip 25-40 mm
4
4
Hose 38 mm
2 m
2 m
Base plate
1
1
Screws and nuts
4
4
Safety transformer
-
1
Please read this operating instruction thoroughly before you start the waterfall
MAMBA
or
MAMBA
LED/BIRDIE LED.
Safety instructions
• The power supply of pump and LED-lighting must meet the product specifi cations. Do not connect the pump, LED-lighting and power supply cable, if the power supply does not
meet the specifi ed regulations! Further information can be obtained from your local approved electrical installation specialist.
• The plug connection of the pump and LED-lighting must be more than 3.5 m away from the swimming pool or garden pond.
• The power supply of the pump and LED-lighting must be via a safety transformer or earth leakage circuit breaker (FI-switch) with a rated fault current ≤ 30 mA. Always use a
safety transformer IP X4 for the LED-lighting in outside areas.
• The power supply cable of the LED-lighting cannot be replaced. The device cannot be used any more if the cable is damaged and must be disposed properly.
• The power supply must always be disconnected during assembly or disassembly and maintenance of the pump and LED-lighting.
• The devices are not suitable for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless these have
been supervised by a person responsible for their safety or have been instructed regarding the use of the device. Children must be supervised in order to ensure that they are not
playing with the devices.
Installation
Swimming pool with sand fi lter system
1.) Pool with wood pool edge
• Place the waterfall element at the selected place on the wood pool edge of your swimming pool.
• Ensure that the hose connection for the waterfall element can be connected without problem to the existing water return from the fi lter to the pool.
• Then prepare the waterfall element for connection with the water return system according to fi gure 1.
• Use the base plate for marking the drill-holes for the screws, cut-out for hose and LED-lighting cable (
MAMBA
LED/BIRDIE LED). See fi gures 2a, 2b and 2c. Pay attention to the
position and wall thickness of the wood construction of your swimming pool.
• You can then rigidly install the waterfall element on the wood pool edge and connect the hose with the supplied screws and nuts. See fi gures 2d and 2e.
• For
MAMBA
LED/BIRDIE LED: Check the LED-strip for correct fi t, install the lighting cable outside the swimming pool and connect it to the safety transformer.
• Check the whole water circuit again for leaks. Leaking screwed or hose connections must be sealed with commercially available Tefl on-tape.
1
Operating Instruction for Stainless Steel Waterfalls
MAMBA
/
MAMBA
LED / B
IR
DIE LED
MAMBA
/bridie manual 2012.indd 10
15-12-12 20:45
