UAS SMOG-HOG PSH Скачать руководство пользователя страница 19

Страница: 19 / 40

revised 10/09

Smog-Hog

PSH Series Model

4. OPERATION

4.1 Start-up Checks

4.1.1 INSTALLING COMPONENTS

if ionizers, collector cells and filter media were removed

for shipment or installation, refer to figure 5 for proper

installation and electrical contact alignment. filter

media is installed as after filters (after the collector

cells) with in-Place cleaning. Do not install filter

media as pre filters (before the ionizers) with in-Place

cleaning. this will reduce the effectiveness of the

wash cycle by 50 percent. the filter media is utilized

as pre and after filters if the PSH is not equipped with

in-Place cleaning. the PSH inlet plenum, if supplied

by uaS, will have baffle filters or aluminum media.

the inlet plenum should be inspected that all baffle

filters or aluminum filters are installed.

4.1.2 dUCTING CONNECTIONS

Blower speeds are factory set by the blower

manufacturer to compensate for static pressure losses

in ducting as specified by others. Starting the blower

before ducting is complete or before debris is removed

can result in motor overload or other system damage.

4.1.3 BLOWER ROTATION

for proper airflow, the blower should be operating in

the correct direction. if the blower is operating in the

reverse direction, air will move in the proper direction,

but at significantly reduced rates. to check rotation:

1. Place PSH unit off line.
2. remove blower housing from the blower to

observe the pulley rotation.

3. Place the PSH unit on line for approximately one

minute.

4. Place PSH unit off line.
5. as the blower pulley slows down, observe the

direction of rotation.

6. note directional arrow located on the blower

housing.

Extreme care should be exercised when operating

blowers with motor/drive belts exposed. Loose

fitting clothing can easily be drawn into these

moving parts.

7. if blower wheel was not rotating in the correct

direction, disengage main three-phase fused

disconnect switch.

WARNING

do not attempt to rewire “live” electrical

connections.

8. open power panel and reverse any two of the three

wires at the terminal strip (Ll, L2, and L3).

9. engage the main three phase fused disconnect

switch and place the PSH on line, checking blower

rotation.

4.1.4 BLOWER BELT TENSION

the drive belt tension adjustment is critical within the

first 24 hours of the system exhaust blower operation.

During this 24 hour period, the initial stretch of the

belt occurs which requires a belt tension adjustment.

if this tension adjustment is not completed the belt will

wear prematurely, requiring a replacement. a drive belt

tension gage should be used for adjusting belt tension.

if fan belt tension is improper, set tension by adjusting

the motor slide base. Loosen four bolts holding the

motor to the base and turn the adjustment bolt(s) on

the base. check with a steel straight edge to make

sure that motor pulley and blower pulley is still aligned.

tighten motor mounting bolts. figure 11 illustrates

a typical motor/blower arrangement (motor/blower

configurations will vary).

Figure 11

Typical Motor/Blower Configuration

CAUTION

Improper tension on drive belts will cause

premature failure of belts.

Содержание SMOG-HOG PSH









































Результаты поиска

Содержание SMOG-HOG PSH

Отзывы:

Похожие инструкции для SMOG-HOG PSH

Бренды по названию

Популярные бренды

UAS SMOG-HOG PSH, Руководство пользователя

Результаты поиска

Содержание SMOG-HOG PSH

Отзывы:

Похожие инструкции для SMOG-HOG PSH

Бренды по названию

Популярные бренды