U.S. Guitar Kits Acoustic Guitar Kit Скачать руководство пользователя | Manualshive

Страница: 36 / 39

background image

36

36

Step Twenty Three-Finishing

You will want to apply a top coat of finish to the instrument to protect the
bare wood from dirt and oils. There are countless finishing products to use
and will post on our website forum, feedback from those that have already
built kits. Many builders use nitro-cellulose lacquer but there are many
precautions needed to use this product. There are many water-borne products
available that are less volatile and less hazardous. Also, there are some nice
hand rubbed oil finishes that require much more work but with spectacular
results. We suggest several tests on scrap woods to find the perfect finish
before working directly on your new instrument.

We hope that you have enjoyed the process and have an instrument that you
will show to others. Hopefully, you or someone you have made this for will
begin to play this with the appreciation of all your time and efforts.

Thanks again for purchasing a kit from US Guitar Kits, Inc.
We would love to see a picture of your finished guitar.
Visit our site at www.usguitarkits.com or send us an e-mail at

[email protected]

.

Safe building and happy playing!!!!!

Copyright

©

2010 by U.S. Guitar Kits, Inc.

All rights reserved.

«
...
34
35
36
37
38
...
»

Содержание Acoustic Guitar Kit








































Отзывы:

Нет отзывов

Похожие инструкции для Acoustic Guitar Kit

Бренд: Parker Страницы: 2

RockBass Fortress

Бренд: Warwick Страницы: 1

Бренд: Vox Страницы: 68

Бренд: Alvarez Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды