U.S. Guitar Kits Acoustic Guitar Kit Скачать руководство пользователя | Manualshive

Страница: 15 / 39

background image

15

15

6)  Using  approximately  25-30  spools
clamps, continue clamping about ¾” apart.
7)  Set  the  assembly  aside  until  the  glue
sets.  With  aliphatic  resin  (white  or  yellow
glue) this means about 1 hour, preferably 2
hours.
8) Remove clamps.

Note:

Make sure the clamping pressure is

over  the  sides  and  not  over  the  middle  or
way  over  the  sides  as  this  will  crack  the
top and likely create irreversible damage.

Note:

We suggest spool clamps that can be

hand tightened with medium, even pressure. Over tightening clamps is
unnecessary and creates unneeded stresses.

So far….so good!
You have now completed all the steps to complete the top installation.

Student Notes:

«
...
13
14
15
16
17
...
»

Содержание Acoustic Guitar Kit








































Отзывы:

Нет отзывов

Похожие инструкции для Acoustic Guitar Kit

Eric Clapton Stratocaster

Бренд: Fender Страницы: 1

Lone Star Stratocaster

Бренд: Fender Страницы: 1

Classic Series 60s Telecaster W/Bigsby

Бренд: Fender Страницы: 1

Spirit XT-2 Standard Bass

Бренд: Steinberger Страницы: 1

Lone Star Stratocaster

Бренд: Fender Страницы: 1

Бренд: Pyle Страницы: 10

Бренд: MGA Entertainment Страницы: 1

Бренд: MGA Entertainment Страницы: 28

ELECTRIC GUITAR & BASS

Бренд: First Act Страницы: 2

Discovery FE433

Бренд: First Act Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды