U.S. Guitar Kits Acoustic Guitar Kit Скачать руководство пользователя | Manualshive

Страница: 1 / 39

background image

Copyright

© 2010 by U.S. Guitar Kits, Inc. All rights reserved.

U.S. Guitar Kits, Inc.

Assembly Instructions for Acoustic Guitar Kit

Welcome

Thank you for purchasing the kit. All the guitar components needed to build
your guitar are included to build a fine instrument. You will need glue,
finish, a variety of ordinary woodworking tools and average woodworking
skills. Knowledge of the use and sharpening of scrapers is crucial and
included is a set of instructions for this tool from a tool supplier.

Please note that although we warrant this kit to be free from defects in
materials and workmanship for 30 days from purchase, we cannot guarantee
the outcome of your instrument since skill levels vary greatly. If you take
your time and follow these instructions precisely and in the order in which
they are presented you will be rewarded with an instrument of which you
can be proud for a lifetime. Take your time, work carefully. Please keep
your kit sealed until ready to use to avoid problems due to moisture and
humidity. We will not replace parts that have been affected by moisture.

Always use safe methods while working and employ all safeguards
including safety glasses and other personal safety devices.

1
2
3
...
»

Содержание Acoustic Guitar Kit








































Отзывы:

Нет отзывов

Похожие инструкции для Acoustic Guitar Kit

Бренд: Ovation Страницы: 10

Бренд: Yamaha Страницы: 2

Special Edition Custom Telecaster FMT HH

Бренд: Fender Страницы: 24

CONTEMPORARY AND STANDARD GUITARS

Бренд: Fender Страницы: 38

Legacy Elite Special4

Бренд: Zon Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды