background image

USER GUIDE

Ordering Replacement Parts

Ordering Replacement Parts

Parts may be ordered online at www.U-Line.com

See our contact information below:

www.U-LineService.com (with service login)
Phone Number: 

+1.414.354.0300

NOTICE
Use only genuine U-Line replacement parts. 
The use of non-U-Line parts can reduce speed 
of ice production, cause water to overflow from 
ice maker mold, damage the unit, and void the 
warranty.

Warranty parts will be shipped at no charge after U-Line 
confirms warranty status. Please provide the model, serial 
number, part number and part description. Some parts will 
require color or voltage information.

If U-Line requires the return of original parts, we will

 

inform you when the parts order is taken. This

 

requirement will be noted on your packing list. A 
prepaid shipping label will be emailed to you. Please 
enclose a copy of the parts packing list and be sure the 
model and serial numbers are legible on the paperwork. 
Tag the part with the reported defect.

Customers and non-authorized servicers may order non-
warranty parts at www.u-line.com. Authorized servicers 
with a servicer login may order non-warranty parts at 
www.u-lineservice.com.

29

Содержание UMCR114-SC01A

















































Отзывы: