U-Line UHFZ124-SS01B Скачать руководство пользователя

Страница: 39 / 46

USER GUIDE

u-line.com

Control Operation-Service

USER GUIDE

Control Operation - Service 4

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE •

SERVICE

14. VIEW ERROR LOG

A list of the errors in the order they occurred will

scroll once on the display. All errors are logged

in memory. Only door error is displayed on the

display and has an audible signal.

E0:

Door 1 (upper) open.

E1:

Thermistor 1 open.

E2:

Thermistor 2 open.

E3:

Thermistor 3 open.

E4:

Thermistor 4 open (Does not apply to this

model).

E5:

Thermistor 1 shorted.

E6:

Thermistor 2 shorted.

E7:

Thermistor 3 shorted.

E8:

Thermistor 4 shorted (Does not apply to this

model).

E9:

Door 2 (lower) open.

P1:

Pump Circuit open (Does not apply to this

model).

15. CLEAR ERROR LOG

To clear errors, press and hold

(5 seconds)

when CLR is flashing.

16. THERMISTOR — 1 DIFFERENTIAL

This number should not be adjusted.

17. EVAPORATOR FAN DELAY IN MINUTES —

“Fan Delay On” is the amount of time in minutes

the fan will be delayed from starting from the

beginning of a cooling cycle. Adjustable 0-99

minutes.

18. EVAPORATOR FAN DELAY IN MINUTES —

OFF

“Fan Delay Off” is the amount of time in minutes

the fan will continue to run at the end of a

cooling cycle. Adjustable 0-99 minutes.

19. INDIVIDUAL COMPONENT TOGGLE

20. MODEL NUMBER INDICATOR

Displays the two-digit model number of the

specific unit. See model list table.

21. LIGHT ALL LED SEGMENTS

This will illuminate all the LEDs on the display to

ensure they work properly.

22. VIEW DEFROST CYCLES

Displays the number of defrosts that have

occurred in the past 24 hours.

23. VIEW COMPRESSOR RUNTIME

This will show the number of minutes the

compressor has run in the prior cycle (or

current cycle if the compressor was running

when service mode was entered).

24. ACTIVATE DEFROST/HARVEST

Turns on the hot gas bypass valve allowing hot

gas to circulate through the evaporator causing

frost to melt.

25. RESTORE FACTORY DEFAULTS

Will restore all adjustable functions to their

factory settings.

26. SOFTWARE VERSION — MAIN BOARD

Displays software version of the main control

board.

27. SOFTWARE VERSION —

USER INTERFACE

Displays software version of the user interface.

28. LOG IN PERIOD

Factory use only - do not adjust.

29. FACTORY TEST MODE

Should be 0.

0. EXIT SERVICE MODE

Display #

Relay/Output

Exit

Relay 2

Relay 3

Relay 4

Relay 5

Relay 6

Relay 7

DC Output 1

DC Output 2

DC Output 3

DC Output 4

DC Output 5

SEE RELAY/OUTPUT CHART

Содержание UHFZ124-SS01B















































Результаты поиска

Содержание UHFZ124-SS01B

Отзывы:

Похожие инструкции для UHFZ124-SS01B

Бренды по названию

Популярные бренды

U-Line UHFZ124-SS01B, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание UHFZ124-SS01B

Отзывы:

Похожие инструкции для UHFZ124-SS01B

Бренды по названию

Популярные бренды