background image

USER GUIDE

u-line.com

Remove Fan and Cover

Remove Fan and Cover

CONVECTION COOLING

This unit is equipped with an advanced convection cooling 
system. Convection cooling stabilizes cabinet temperature, 

cools product faster and increases energy efficiency.

Evaporator Fan

The evaporator fan is responsible for circulating warm air 
from the refrigeration zone, past the evaporator and back 
into the refrigerated zone.

The evaporator fan is factory set to have a 1 minute delay 
at the beginning of a cooling cycle. This delay gives the 
evaporator time to cool properly before warm air is passed 
over it. The fan will continue to run for an additional 2 
minutes at the end of a cooling cycle. Fan delay times can 

be modified through the service menu.

Evaporator fan operation is also determined by door switch 
state. If the door switch circuit opens, the fan will stop. 
When the door switch circuit is closed the fan will either 
continue running with the cooling cycle, or if not currently 
cooling, the fan will run for 1 minute to circulate air and 
clear any condensation that may have appeared on glass 
doors and shelves.

Note:

 If the unit is set to sabbath mode, the evaporator 

fan will no longer respond to the state of the door switch.

In order to operate efficiently, the evaporator fan blade 

and vents should be unobstructed and free of any dust 
buildup.

Evaporator Fan Replacement

Should the evaporator fan need to be replaced follow the 
steps below.

1.  Remove any product from the unit.

2.  Remove unit from cabinetry to access rear.

3.  Disconnect power to the unit.

4.  Remove back panel from unit.

5.  Disconnect fan electrical connection at rear of unit.

6.  Remove insulating foam from refrigerant line pass-

through hole as needed to gain clearance for fan plug.

7.  Remove internal shelving.

8.  Remove rear shelf clips, fronts can remain.

9.  Remove thermistor cover.

10.   Remove two evaporator cover screws from top of 

evaporator plate.

11.  Grasp evaporator cover, pull forward and up as bottom 

of cover is installed behind the front edge of the drain 
trough.

12.  While pulling the evaporator cover clear of the unit, it 

may be necessary to use your free hand to manipulate 
the fan plug end through the pass-through hole.

13.  Remove the 4 screws mounting the fan shroud to the 

evaporator plate.

Evaporator Cover

Screws

Air Flow

55

Содержание UCDE224ESS03A


























































Отзывы: