background image

SS1095

5

MARINE SERIES

Origins Ice Maker
Model SS1095

All Origins Ice Makers provide high daily ice production 
and storage capabilities, and conserve on water, using 
only 2-3/4 gallons (10.4 L) to produce approximately 22 lbs 
(10 kg) of ice.

• Model SS1095 produces up to 23 lbs (10.4 kg) of ice per 

day and will store 12 lbs (5.4 kg). 

• The unit features a clear, removable ice bucket.

• Occasional manual defrosting will be required.

• Models SS1095 door features custom Stainless side 

handle that is field reversible.

Features and specifications are subject to change without 
notice.

Figure 2

IMPORTANT

IMPORTANT

Proper air flow is required for your unit to operate 
at its highest efficiently. A grille, located in the base 
of the unit (Figure 2), must not be blocked at any 
time, or your unit will not perform as expected.

Initial Startup

All U-Line units are shipped with controls that are preset. 
No initial adjustments are required. 

IMPORTANT

IMPORTANT

It is possible that dirt or scale will dislodge in the 
water line. Always throw away all ice cubes made 
during the first two to three hours of operation.

The power switch is located behind the front grille. A 
small opening in the top of the grille 

(Figure 2)

 is 

provided to access the switch. 

Figure 3

Depress the ON/OFF switch 

(Figure 3) 

as required to turn 

the unit on or off.  

Ice Harvest Control

Adjustments are not normally needed. The control is 
preset at the factory.

IMPORTANT

IMPORTANT

Making adjustments may affect the daily ice 
production of the unit.

To adjust the Ice Harvest Control:

1. Remove the front grille (one screw)

 (Figure 2)

.

Figure 4

2. Turn the adjusting screw 

(Figure 4) 

using a flat tip 

screwdriver in a small increment clockwise for a COLDER 
setting (slower ice production) or counterclockwise for 
a WARMER setting (faster ice production).

3. Replace the front grille (one screw).

Ice Maker

When the ice bucket is full, the ice making mechanism will 
shut off. However, the refrigeration system will continue 
to cool and maintain the cube supply.

IMPORTANT

IMPORTANT

Do not place cans or bottles in the ice compartment 
because they will freeze.

4 Product Features

5 Operation

ULIN_1038_A

Model

SS1095FC

Model

SS1095FD

Grille

screw

ULIN_0129_A

OFF

ON

C

OLDER 

ULIN_0131_A

Содержание SS1095

















Отзывы: