background image

PAGE 6 OF 6 

1018 IH-7357

LCD DISPLAY CONTINUED

TROUBLESHOOTING

Backward Current Protection – Fault/Error Code: 

0000

•  Once the engine has been started, the unit will 

turn off after five seconds of sensing large current 

charging, typically due to the initial alternator surge, 

which can be greater than 50 amps.

•  After the engine starts, disconnect the black clamp (–) 

and then the red clamp (+).

Over-Charge Protection – Fault/Error Code: 

0000

•  Once the battery is fully charged, the charging 

circuit automatically senses full charge and turns off 

charging.

•  Remove charge cord, and press and hold power 

button to turn off unit.

Overloaded USB Output Port – Fault/Error Code: 

0000

•  If the unit senses a current overload from either of 

these ports, the unit will flash fault/error code 

0000

  

and turn off completely.

•  Remove USB device and discontinue use of device 

with this unit.

OPERATING ISSUE

CAUSES

RECOMMENDATIONS

The unit won't jump 

start car.

Clamps are not making a good 

connection to the battery.

The unit is not charged.

The vehicle's battery voltage is 

over 15V.

The vehicle does not have a 

battery.

The temperature of the jump 

starter’s internal battery is low.

Check for poor connection to 

battery. Make sure connection 

points are clean.

Check the battery charge status 

and recharge unit if necessary.

You cannot use this jump starter 

for this vehicle.

Follow the instructions on how to 

use the Override Mode function.

Place the unit indoors at 

temperatures above 32°F until 

warm.

The unit won't power 

USB device.

The device is not turned on.

The jump starter is turned off.

Turn on the device.

Turn unit on, if internal battery of 

the jump starter is low, recharge.

Inspect all attachments for:

•  Cuts or abrasions in the cable.

•  Cracks or broken connectors.

•  Excessive corrosion on any connections.

•  Damaged housing.

•  Broken LCD.

WARNING! If any of these problems are found, 

discontinue using the jump starter and contact 
Uline Customer Service at 1-800-295-5510.

π

  CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA

1-800-295-5510

uline.com

Содержание RESCUE H-7357







Отзывы: