U-Line pmn Скачать руководство пользователя страница 18

NORMAL OPERATION

On units with refrigerator sections, the unit has been designed to
achieve a fresh food temperature of approximately 38°F. Those units
with a freezer section are designed to have a freezer temperature of
approximately 0°F.

On units with ice makers, when the ice buck-
et is full, the ice making mechanism will shut
off. However, the refrigeration system will
continue to cool and maintain the cube sup-
ply. Frost free icemaker units have lower ice
production than manual defrost units.

Ice production may be interrupted by raising
the bin arm into an upright and locked posi-
tion (the unit will maintain temperature for
ice storage, see Figure 20).

Certain sounds are normal during the unit’s operation. You may hear
the compressor or fan motor, the water valve, sounds of defrost, or
ice dropping into the ice bucket.

NEVER use an ice pick, knife, or other sharp instrument to
separate cubes. Shake the ice bucket instead.

The ice bucket MUST be fully inserted to avoid freezing products in the
refrigerator section of the Combo 2075FF.

During periods of limited usage or high ambient temperatures, it is
common for cubes to fuse together. Shake the bucket to break apart
cubes.

If ice maker is not used regularly, the ice bucket should be emptied peri-
odically to ensure fresh cubes.

It is normal for cubes to appear cloudy. This is caused by air being
trapped in the water due to fast freezing. It has nothing to do with the
health, taste or chemical make-up of the water. It is the same air that
is in every glass of water you drink.

!

WARNING

16

User’s Manual

UL002A

Figure 20

Содержание pmn

































Отзывы: