U-Line H-2086 Скачать руководство пользователя страница 2

PAGE 2 OF 6 

0421 IH-2086

ASSEMBLY CONTINUED

Figure 3

Figure 4

Figure 5

ATTACH NOSE PLATE, FOLDING NOSE EXTENSION 

AND AXLE SUPPORTS

1.  Position frame reinforcements against bottom frame 

rail. (See Figure 2a) Slide nose plate into channel on 

frame reinforcements, keeping bolt holes aligned. 

(See Figure 2)

2.  Align axle support with outside rail of frame.  

(See Figure 2)

3.  Insert four 8mm bolts through the axle supports, 

frame, frame reinforcements and nose plate.  

(See Figure 2)

4.  Slide the folding nose extension bracket over the 

8mm bolts protruding from the bolt holes on the 

inside of the noseplate. (See Figure 3a)

NOTE: The bolt holes on the bracket are NOT 

centered. Make sure the bolt holes are closest 
to the back of truck before tightening.  
(See Figure 3)

5.  Secure with locknuts but DO NOT tighten. (See Figure 3)

ATTACH AXLE AND WHEELS

1.  Lay hand truck down on front so axle supports face 

upwards. (See Figure 4)

2.  Insert axle through holes in axle supports. Align holes 

in axle with grooves on inside of the axle supports. Use 

a hammer to tap in the round pins. (See Figure 4a)

Frame

Reinforcements

Frame

Figure 2

Figure 2a

Round 

Pin

Axle

3.  Slide a washer onto each end of the axle. Slide 

a wheel onto each end of the axle. Slide another 

washer onto each end of the axle. (See Figure 5)

4.  Insert a cotter pin through the holes in each end 

of the axle. Bend cotter pins using pliers to secure 

wheel. Wheels should spin freely. (See Figure 5)

5.  Tighten all locknuts.

6.  Check tire pressure (30 PSI max). Inflate if necessary.

Figure 4a

Figure 3a

1-800-295-5510

uline.com

Содержание H-2086







Отзывы: