U-Line H-140 Скачать руководство пользователя страница 5

PAGE 5 OF 5 

0815 IH-140

OPERATING ISSUE

RECOMMENDATIONS

Centerfold shrink film will not 

separate or open.

If shrink film appears to be single sheet, place a strip of tape on top 

of the film and on the bottom and pull apart to initially separate.

Film appears to smoke or is 

sticking to wire when seal is 

made.

This can mean one of several things:

1.  With PP or PO film, wire must be kept clean by removing sealing 

pad and depressing arm until wire burns clean all film residue. 

No teflon tape required on arm.

2.  PVC film will smoke when seal is made. Teflon tape over the 

heating element will prevent the film from smoking and will 

occasionally need to be replaced. 

For teflon tape or other 

parts, call Uline at 1-800-295-5510.

Burning holes in shrink film with 

the heat gun.

If gun is set on high temperature and held in the same spot for more 

than a few seconds, the film will burn. Gun should be continually 

moving in a circular spiral motion from the outside edges of the 

package first, and to the middle of the package last. 

Arm is not properly cutting 

and sealing shrink film.

1.  On/Off switch may not be turned on.

2.  Timer on Industrial model may not be set properly.

3.  Arm may not be in complete contact with pad. (Gentle Pressure).

4.  Excessive pressure applied to sealing arm.

5.  Wire may need cleaning.

Setting timer properly.

Timer should be set to allow the minimal amount of time necessary 

to cut and seal the film. The setting will vary according to type 

of film in use. Setting timer too high will burn the film. PVC film will 

require a lower setting than most other films. Timer may need to 

be adjusted to lower setting as machine is used in a continuous or 

rapid manner.

Package is ballooning when 

the film is heated.

The air inside the package expands as the film is heated. The 

quickest way to vent the film is to cut an asterisk (*) into the closed 

end of the centerfold. The smaller your package, the more lines you 

should cut to make sure every package has at least one vent hole.

TROUBLESHOOTING

Closed end of

centerfold

Open end of

centerfold

Cut slits

π

  CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA

1-800-295-5510

uline.com

Содержание H-140






Отзывы: