U-Line H-140 Скачать руководство пользователя страница 4

PAGE 4 OF 5 

0815 IH-140

SHRINK WRAP SYSTEM

1.  Plug power cord into 110 VAC 15 A wall outlet.

2.  Turn power on by depressing rocker switch. No 

warm-up time is required.

3.  Plug the heat gun into AC outlet on left hand side  

of box.

4.  Separate film and place around spreader bar.  

(See Figure 1)

5.  Pull film to the desired length on the left hand side  

of sealing arm and sealing pad. Open film and  

insert package. Roll excess film back onto the roll  

so that package is approximately even with edge of 

sealing pad.

6.  Adjust dial to proper setting. Holding package in 

left hand, bring the sealing arm down firmly onto 

the film and pad until the LED indicator turns off. 

Gently pull package away in a tearing motion 

until package is completely separated from pad. 

Release the arm and turn the package counter-

clockwise 90°. Repeat to seal the remaining edge of 

film. (See Figure 2)

NOTE: If the cutting and sealing process takes 
longer than 3 to 5 seconds, turn up the dial on 
the machine. If this does not reduce the dwell 
time, call Uline for assistance at 1-800-295-5510.

7.  To shrink film around the product: adjust heat gun to 

desired temperature. Holding gun approximately 12" 

from product, begin to shrink film around the seams 

first and then toward the middle in a circular motion 

until package has a glass-like appearance.  

(See Figure 3)

NOTE: Do not hold gun in the same position for 
more than a few seconds. This will cause the 
film to burn rather than to shrink.

WARNING! Heat gun should not be left on when 
air intake vents are blocked or for a prolonged 
period of time to prevent overheating! Make 
certain that switch is in the off position to ensure 
that both the blower and heating element are 
shut off, or heat damage may occur.

8.  Always turn your Shrink Wrap System off when not in use.

OPERATING INSTRUCTIONS

Figure 1

Figure 3

Figure 2

Содержание H-140






Отзывы: