manualshive.com logo in svg

U-Line Echelon CLRCO2175S41, Руководство по установке

Поделиться
Скачать
U-Line Echelon CLRCO2175S41 Скачать руководство пользователя страница 23

03/2008

23

www.U-LineService.com

CLR2160/CLRCO2175 Ice Makers

Initial Start-Up

Once installation and leveling is complete, the unit is 
ready for initial start-up and operation. The display panel 
is located inside the unit, on the top of the refrigerator 
side (see 

Figure 53, 1

). 

The LED display shows the temperature set point 
and is calibrated in degrees Fahrenheit. The 
controller is factory programmed for a set point of 
38°F which will show when the unit is first powered 
up.

1. Open the door and remove the cover in front of the 

evaporator by gently compressing and pulling 
forward. This will enable you to observe the water 
flow over the evaporator.

2. Check that the overflow tube is inserted securely into 

the water trough.

3. Press the POWER icon (see 

Figure 53, 1

) and hold for 

approximately five seconds until the °F symbol flashes 
and release. The water fill valve will energize and fill 
the water reservoir. The water fill valve shuts off after 
approximately 180 seconds (3 minutes). The compressor 
begins to operate.

The CLRCO2175 display (see 

Figure 53, 3

) will show 

the set-point temperature (38°F) when the unit is on 
and will show OFF when the unit is off. The CLR2160 
display (see 

Figure 53, 3

) will show ICE when the unit 

is on and will show OFF when the unit is off.

4. Watch the water flow over the evaporator assembly (ice 

cube tray) to familiarize yourself with the operation. 
Upon initial start-up, water flow over the evaporator 
may be uneven. This may cause uneven sized cubes or 
water spilling into the ice storage bin. This is a normal 
situation and will correct itself within the first 24 hours 
of operation. 

5. Replace the evaporator cover. Note that after the first 

slab of ice is produced, ice production will stop until the 
refrigerator side of the CLRCO2175 reaches the set 
point temperature. Then, ice production will begin 
again.

6. Allow unit to run for at least 24 hours to stabilize 

before making any temperature or ice adjustments.

IMPORTANT

It is possible that dirt or scale will dislodge in the water 
line. Always throw away all ice cubes made during the 
first two to three hours of operation.

Other Settings

Other settings for the unit are factory preset. No 
adjustments should be necessary at this time. For 
information about Ice Cube Thickness, or additional 
settings, see the Use and Care Guide.

10 Start-Up for the First Time

1

2

3

5

4

ULIN_0058_A

Figure 53

Содержание Echelon CLRCO2175S41

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды