manualshive.com logo in svg

U-Line Echelon CLRCO2175S41, Руководство по установке

Поделиться
Скачать
U-Line Echelon CLRCO2175S41 Скачать руководство пользователя страница 11

03/2008

11

www.U-LineService.com

CLR2160/CLRCO2175 Ice Makers

2. Create a relief (

Figure 19

) for pivot plate by cutting 

notch in top corner of overlay panel. Refer to 

Figure 

20

 for exact specifications.

Route notch in top corner of overlay panel as shown 
(see Top and Side Views). Top of notch is entire depth 
of panel, front to back. 

Width: 31/32"

Depth: 1/8"

CAUTION

Be careful not to drill too deep! Drilling holes too deep 
may destroy your door panel.

3. Drill hole for upper door hinge (top of panel) (see 

Figure 20

, Top View).

0.177" diameter

(#16 drill) x 11/16" deep

4. Drill hole for lower door hinge (see 

Figure 20

, Bottom 

View).

5/16" diameter x 1/4" deep

CAUTION

It is important to ensure that all drilled holes are drilled to 
the correct depth in order to avoid splits in the wood 
when hardware is installed.

Installation Instructions

Removing Existing Door

1. Remove the door shelves by first pulling shelves up at 

a 45° angle, then straight out.

2. Remove top hinge screw pin (Phillips screwdriver). 

Remove the door by tilting forward and lifting off the 
bottom hinge pin.

3. Pull door gasket out of the groove (top edge of door 

only). Start in the middle and pull outward, moving 
toward the edge (see 

Figure 21

). This may take some 

force.

4. Remove the two screws located on both sides of the 

handle.

5. Remove the handle and discard. (This handle will be 

replaced with the Overlay Handle included in the Full 
Overlay Door Panel Kit. See 

Figure 22

.)

6. Slide the existing door panel out of the doorframe.

Attaching the Full Overlay Panel

1. Place and tape the existing door panel on the back of 

the overlay panel (see 

Figure 23

) and drill holes 

through both panels according to 

Figure 24

. Remove 

tape adjoining the panels and enlarge the six holes in 
the steel (black/white vinyl color) panel using a 0.201" 
(#7) drill.

2. If a user-supplied cabinet handle will be used, attach its 

hardware to the overlay panel at this time.

15/32"

3/8"

.125"

13/32"

31/32"

BOTTOM VIEW

BACK VIEW

SIDE VIEW

TOP VIEW

ø 0.177"  (#16 Drill)

 11/16" Deep

3/4" Min Ref

1/4"  Ref

3/8"

11/16"

Ref

ø 5/16" x 1/4" Deep

Chamfer 1/32" x 45

°

ULIN_0401_A

Figure 20

New Handle

Old Handle

ULIN_0403_A

Figure 21

Figure 22

Содержание Echelon CLRCO2175S41

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды