background image

USER GUIDE

u-line.com

Safety and Warning

Safety and Warning

NOTICE
Please read all instructions before installing, 
operating, or servicing the appliance.

Use this appliance for its intended purpose only and follow 
these general precautions with those listed throughout this 
guide:

SAFETY ALERT DEFINITIONS

Throughout this guide are safety items labeled with a 
Danger, Warning, or Caution based on the risk type:

Danger means that failure to follow this safety 
statement will result in severe personal injury or 
death.

Warning means that failure to follow this safety 
statement could result in serious personal injury 
or death.

Caution means that failure to follow this safety 
statement may result in minor or moderate 
personal injury, property, or equipment damage.

This unit contains R600a (Isobutane) which is a
flammable hydrocarbon. It is safe for regular
use. Do not use sharp objects to expedite
defrosting. Do not service without consulting the
“R600a specifications” section included in the
User Guide. Do not damage the refrigerant
circuit.

Service must be done by factory authorized
service personnel. Any parts shall be replaced
with like components. Failure to comply could
increase the risk of possible ignition due to
incorrect parts or improper service.

CALIFORNIA PROPOSITION 65

This product contains chemicals known to the 
state of California to cause cancer and birth 
defects or other reproductive harm.

www.P65warnings.CA.gov

This equipment is to be installed with adequate 
backflow protection to comply with applicable 
federal, state and local codes.

DANGER

!

DANGER

!

WARNING

!

CAUTION

!

CAUTION

!

WARNING

!

4

Содержание Acr115

















































Отзывы: