U-Line 2260DC Скачать руководство пользователя страница 20

Страница: 20 / 70

USER GUIDE

Integrated Grille - Plinth Dimensions 1

u-line.com

SAFETY •

INSTALLATION & INTEGRATION

• OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Integrated Grille - Plinth
Dimensions

PREPARE AND INSTALL INTEGRATED GRILLE
(PLINTH STRIP/BASE FASCIA)

1. Use the dimensions provided in the diagram to cut and

shape your integrated grille (plinth strip/base fascia)
panel. Recommended panel thickness is between 1/4"
(6 mm) and 3/8" (9 mm).

2. Finish or stain your grille (plinth strip/base fascia)

panel to match your surrounding furniture. Finish
front, back and edges to prevent warping. Carefully
follow the manufacturer’s recommendations for finish
application and cure times.

3. Apply double sided tape to the backside of the

integrated grill (plinth strip/base fascia). Use the
diagram below for reference. U-Line recommends
3M

™

VHB

™

tape, a high strength bonding tape.

4. Remove backing paper from double sided tape.

5. Carefully align grille (plinth strip/base fascia) over

integrated panel and press into position.

INTEGRATED GRILLE (PLINTH STRIP/BASE
FASCIA) DIMENSIONS

Apply Tape To Shaded Area

23-3/4"

(605 mm)

20-5/8"

(525 mm)

1-9/16"

40 mm)

1-9/16"

(40 mm)

1" (25 mm)

3-5/16"

(84 mm)

Содержание 2260DC







































































Результаты поиска

Содержание 2260DC

Отзывы:

Похожие инструкции для 2260DC

Бренды по названию

Популярные бренды

U-Line 2260DC, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание 2260DC

Отзывы:

Похожие инструкции для 2260DC

Бренды по названию

Популярные бренды