u-blox LARA-R203 Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 157

background image

LARA-R2 series - System Integration Manual

UBX-16010573 - R12

Approvals

Page 139 of 157

4.3.2

Modifications

The ISED Canada requires the user to be notified that any changes or modifications made to this device that are
not expressly approved by u-blox could void the user's authority to operate the equipment.

Manufacturers of mobile or fixed devices incorporating the LARA-R2 series modules are
authorized to use the ISED Canada Certificates of the LARA-R2 series modules for their own final
products according to the conditions referenced in the certificates.

The ISED Canada Label shall in the above case be visible from the outside, or the host device shall
bear a second label stating:
"Contains IC: 8595A-1EIQ24NN" resp.
"Contains IC: 8595A-1DIQN3NN" resp.
"Contains IC: 8595A-1EIQN2NN" resp.

Innovation, Science and Economic Development Canada (ISED) Notices
This Class B digital apparatus complies with Canadian CAN ICES-3(B) / NMB-3(B) and RSS-210.
Operation is subject to the following two conditions:

o

this device may not cause interference

o

this device must accept any interference, including interference that may cause undesired
operation of the device

Radio Frequency (RF) Exposure Information
The radiated output power of the u-blox Cellular Module is below the Innovation, Science and
Economic  Development  Canada  (ISED)  radio  frequency  exposure  limits.  The  u-blox  Cellular
Module should be used in such a manner such that the potential for human contact during normal
operation is minimized.
This  device  has  been  evaluated  and  shown  compliant  with  the  ISED  RF  Exposure  limits  under
mobile exposure conditions (antennas are greater than 20 cm from a person's body).
This device has been certified for use in Canada. Status of the listing in the Innovation, Science
and  Economic  Development’s  REL  (Radio  Equipment  List)  can  be  found  at  the  following  web
address:
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng
Additional Canadian information on RF exposure also can be found at the following web address:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

IMPORTANT: Manufacturers of portable applications incorporating the LARA-R2 series modules
are required to have their final product certified and apply for their own Innovation, Science and
Economic Development Certificate related to the specific portable device. This is mandatory to
meet the SAR requirements for portable devices.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.

«
...
137
138
139
140
141
...
»

Содержание LARA-R203






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для LARA-R203

Бренд: Salda Страницы: 20

Бренд: Klimaire Страницы: 5

Бренд: Fuji Electric Страницы: 12

Бренд: heat-timer Страницы: 36

S3500 Series Uplink Module

Бренд: Aruba Страницы: 8

Бренд: Lutron Electronics Страницы: 2

Бренд: Monster Central Страницы: 13

Бренд: Rain Bird Страницы: 18

Бренд: Osaka Страницы: 12

Бренд: M-system Страницы: 7

Бренд: D+H Страницы: 12

Бренд: DUCH Страницы: 9

Бренд: EFI Страницы: 55

Бренд: jablotron Страницы: 2

Бренд: HIMA Страницы: 40

Infi 90 IMCPM03

Бренд: Bailey Страницы: 61

SEPCOM SIP BED Easy

Бренд: WAMGROUP Страницы: 52

Бренд: DH Instruments Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды