background image

 

C030-R412M - User Guide 

UBX-19010121 - R01 

Hardware description  

Page 16 of 27 

 

 

 

Name  Function 

Variant

2

 

R412M 

Description 

R132  InterfaceMCU level translator OE to 

3.3VDC 

 

Links OE input of the level translator to 3.3VDC 

R133  HostMCU USART2 virtual COM Rx link  

 

Link to InterfaceMCU USART2 Rx signal through 1.8V to 3.3V 
level translator 

R134  HostMCU USART2 virtual COM Tx link 

 

Link to InterfaceMCU USART2 Tx signal through 1.8V to 3.3V 
level translator 

R135  HostMCU external system clock (Osc.) 

link 

 

Link to 8 MHz clock generated from InterfaceMCU to drive the 
HostMCU 

R136  HostMCU USART2 USB sniffer Tx link 

 

Link to serial USB sniffer Rx input  

R137  HostMCU USART2 USB sniffer Rx link 

 

Link to serial USB sniffer Tx output 

R142  InterfaceMCU 3.3VDC supply sampling 

 

Utilised for monitoring InterfaceMCU 3.3VDC supply level 

R143  InterfaceMCU level translator OE GND 

link 

 

Links OE input of the level translator to GND to disable the 
translator 

R144  HostMCU PA_0 pull up 

 

HostMCU PA_0-WKUP pin setting 

R145  HostMCU BOOT1 pull up 

 

HostMCU BOOT1 input setting to ‘1’ 

R146  HostMCU BOOT0 pull up 

 

HostMCU BOOT0 input setting to ‘1’ 

R147  Serial USB sniffer reset link 

 

Link between serial USB sniffer’s reset input to the application 
section reset signal 

R149  Cellular Module DTR pull down 

 

SARA-R412M DTR input pull down 

R150  The Si7034-A10 is a Temperature and 

Relative Humidity Sensor power link 

 

Link to 1.8VDC supply rail. See R48 link for utilization. 

R151  Arduino™ interface 1.8V IO supply option 

 

Provisional 

R152  Arduino™ interface IOREF voltage level 

selection for 3.3VDC 

 

Link to Arduino™ interface 3.3V pin  

R153  Arduino™ interface IOREF voltage level 

selection for 5VDC 

 

Link to Arduino™ interface 5V pin 

R154  Arduino™ interface 5V pin to USB5V rail 

 

USB5V supply link for Arduino™ interface 

R160  M_GPIO3 net to PB8 link  

 

Link to Arduino™ interface 

R161  M_GPIO4 net to PB15 link 

 

Link to Arduino™ interface 

R162  GPS_PPS net to cellular module GPIO1 

link 

 

Link to SARA-R412M GPIO1 

R164  IC22 output link to GNSS module 

 

Provisional 

R165  1V8_ZOE supply link to GNSS module 

 

1.8V Supply rail to ZOE-M8B 

R167  IC22 100k resistor 

 

Provisional 

R168  M_GPIO3 net link to cellular module 

 

Link to SARA-R412M GPIO3 

R170  M_VINT net link to cellular module GPIO5 

 

Link to SARA-R412M GPIO5 

R171  Arduino™ interface D5 pin to IC10 link 

 

Provisional isolation 

R172  IC10 A6 pin to PA5 link 

 

Provisional isolation 

R173  PA5 to Arduino™ interface D5 pin direct 

link 

 

Provisional 

R174  USART1_TX net USB sniffer link 

 

Link to S2 switch 

R175  I_GNSS signal connection to Arduino™ 

interface A1 

 

Provisional 

R178  PC8 link to Arduino™ interface D4 

 

Link to Arduino™ interface 

R179  PB1 connection to Arduino™ interface D4  

 

Provisional for backward compatibility 

R180  Cellular module M_SCL net to Arduino™ 

interface SCL pin 

 

Provisional 

R181  Cellular module M_SDA net to Arduino™ 

interface SDA pin 

 

Provisional 

Содержание C030-R412M




























Отзывы: