2.4. Local Diagnostics Test
Before testing, remove the plastic cover and then open the battery cover
(see "Figure 2: Installation" on page 2).
A.
Press the self-test button once and release it; the following
procedure should occur in turn:
The red LED will switch ON and then OFF, the green LED will switch
ON and then OFF, the strobe light will switch ON and then OFF and
the piezo siren will sound to indicate that the siren is now fully
operational.
B.
After 2 seconds the LED blinks 3 times.
The following table indicates received signal strength indication.
LED response
Reception
Green LED blinks
Strong
Orange LED blinks
Good
Red LED blinks
Poor
No blinks
No communication
Important!
Reliable reception must be assured. Therefore, "poor"
signal strength is not acceptable. If you receive a "poor" signal from the
detector, re-locate it and re-test until a "good" or "strong" signal strength
is received.
Note:
For detailed Diagnostics Test instructions refer to the control
panel Installer Guide.
3. Compliance With Standards
The BW-SRO complies with the following standards:
Europe:
EN 300 220, EN 301489, EN 50130-4, EN 62368-1, EN 50130-5, EN 50131-4 self-powered siren, type W, EN 50131-5-3. IP55.
Hereby, Bentel Security S.r.l. declares that the radio equipment type BW-SRO is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
Certified by Applica Test & Certification AS in accordance with EN 50131-4, EN 50130-4, EN 50130-5. Security Grade 2 and Environmental
Class IV.
EN 50131-1 Security Grade:
According to EN 50131-1 this equipment can be applied in installed systems up to and including Security
Grade 2.
EN 50131-1 Environmental Class:
Class IV
UK:
This product is suitable for use in systems installed to conform to PD6662 at Grade 2 and environmental class 4. BS8243.
Warning!
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not returning it for repair then
you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.
Directive 2012/19/EC Waste Electrical and Electronic Equipment.
4. SPECIFICATIONS
Frequency Band (MHz):
868
Maximum Tx Power:
14 dBm @ 868 MHz
Modulation:
GFSK
Antenna:
Built-in antenna
Communication Protocol:
PowerG
Supervision interval:
Signaling at 128 s intervals
Current consumption:
Quiescent mode: 50μA
Alarm sound operated: 430mA
Siren Type:
piezo, 1.4-3.2 kHz, sweep frequency 7 Hz
Sound Level:
minimum 100 dBA @ 1 m
Power Supply:
Type C
Battery Type:
Four 3.6V/3.5Ah Lithium independent cells (EVE and
FANSO ER18505M) assembled in two plastic wrappings and connected
to the cable adaptor (see Figure 2). Bentel assembly catalog no.
PFNBTBLIBW-B35SR.
Note:
Use only the above battery.
Note:
The strobe flashes 5 times and the red LED lights continuously
during first battery installation.
Battery Life Expectancy:
8 years (for typical use)
Low Battery Threshold:
2 V +300 mV negative slope OR 1.2 V
Strobe Light: Pulsed @ 1 sec.
Operating Temperature:
-33°C to 70°C (-27.4°F to 158°F)
RH humidity:
93%
Dimensions (LxWxD):
295x186x63mm (11-5/8 x 7-5/16 x 2-1/2 in)
Weight (including battery):
970g (34 oz)
Color:
White (with blue lens)
WARRANTY
Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only (the “Purchaser”) against defective
workmanship and materials under normal use of the Product for a period of twelve (12) months from the date of shipment by the Manufacturer.
This Warranty is absolutely conditional upon the Product having been properly installed, maintained and operated under conditions of normal use in
accordance with the Manufacturers recommended installation and operation instructions. Products which have become defective for any other reason,
according to the Manufacturers discretion, such as improper installation, failure to follow recommended installation and operational instructions, neglect,
willful damage, misuse or vandalism, accidental damage, alteration or tampering, or repair by anyone other than the manufacturer, are not covered by
this Warranty.
There is absolutely no warranty on software, and all software products are sold as a user license under the terms of the software license agreement
included with such Product.
D-308696 BW-SRO Installation Guide
4
