Tyco ACC-1 Скачать руководство пользователя страница 33

Страница: 33 / 38

Appendix G of TFP1090 (07/2020)

Summary Instructions (if problems occur, consult full document)

DN65 and DN80, Model DPV-1 Dry Pipe Valve with Three-Way Alarm Test Valve,

with Model ACC-1 Accelerator

422 mm

367 mm

776 mm

185 mm

I. Normal Conditions

• The Main Control Valve (A) is opened

and locked, and the Accelerator

Control Valve (S) and Air Supply

Control Valve (K) are open.

• The sprinkler system is filled with air

and is pressurized.

• The Main Drain Valve (F), and Low

Body Drain Valve (L) are closed.

• The Three-Way Alarm Control Valve

(E) is in the open position.

• The Pressure Gauge Valves (B) and

• The Pressure Switch Valve (J) is

open.

• System Air Pressure Gauge (G)

reads downstream air pressure,

Water Supply Pressure Gauge (H)

reads the upstream water pressure,

and Accelerator Air Pressure Gauge

(R) reads the accelerator pressure.

II. Operation

When one or more sprinklers are acti-

vated, the accelerator operates to per-

mit system air pressure into the Dry

Pipe Valve intermediate chamber. Doing

so will immediately overcome the ability

of the system air pressure to hold the

Dry Pipe Valve closed without having

to wait for system air pressure to de-

cay to approximately 20% of the water

supply. The Dry Pipe Valve immediately

opens to permit water flow into the sys-

tem piping and to be discharged from

any open sprinklers. Also, with the Dry

Pipe Valve open, water flows to actuate

the Waterflow Pressure Alarm Switch

(M) and, as applicable, the Water Motor

Alarm.

III. Removing System From Service
Step 1.

Close the Main Control Valve

(A), close the Air Supply Control Valve

(K), close the Accelerator Control Valve

(R), and place the Three-Way Alarm

Control Valve (E) in the closed position.

Step 2.

Drain the system with the Main

Drain Valve (F) and by opening all auxil-

iary drain valves in the system to make

sure that cross-mains and branch lines

are drained.

IV. Placing the System Back in

Service
Step 1.

Close the auxiliary drain valves

after water ceases to discharge, and

leave the Main Drain Valve (F) open.

Step 2.

Place the Three-Way Alarm

Control Valve (E) in the open position.

Step 3.

Replace the sprinklers that

have operated and the sprinklers close

to the fire.

Step 4.

Push down on the reset knob

(P) to allow the Dry Pipe Valve (D) to

re-seat.

Step 5.

Via the Air Supply Control

Valve (K), pressurize the system with

air to 0,7 bar, and then open and close

each auxiliary drain valves in the sys-

tem piping to drain any remaining water

in trapped sections. Also, partially open

the Low Body Drain Valve (L) to assure

that the riser is completely drained.

Close the Low Body Drain Valve (L) as

soon as water ceases to discharge.

Step 6.

Open the Air Supply Control

Valve (K) to restore the system to the

normal system air pressure.

Step 7.

Reset accelerator (Q) using the

instruction on its resetting label.

Step 8.

Partially open the Main Control

Valve (A), and then slowly close the

Main Drain Valve (F).

Step 9.

Fully open the Main Control

Valve (A) and lock it open.

Step 10.

Reset the fire alarm panel

and notify the central alarm station.

V. Weekly Test

Important:

Prior to closing any valves

or activating any alarms, notify local se-

curity guards and the central alarm sta-

tion if applicable.

Step 1.

Place the Three-Way Alarm

Control Valve (E) in the test position,

verify that the alarm signal created by

the Waterflow Pressure Alarm Switch

(M) is visible at the fire panel. If appli-

cable, check the sound of the Water

Motor Alarm — it must be clear and

steady.

Step 2.

Place the Three-Way Alarm

Control Valve (E) in the open position

and verify that the normal supply and

system pressures are restored. If the

supply pressure is below the normal,

use the instructions from the water sup-

ply to obtain the usual pressure.

Step 3.

Close the Pressure Switch

Valve (J) and verify operation of the low

air pressure Alarm Switch (N).

Step 4.

Return the Pressure Switch

Valve (J) to the normally open position

after verifying that the alarm signal is

visible at the fire panel.

Содержание ACC-1







































Результаты поиска

Содержание ACC-1

Отзывы:

Похожие инструкции для ACC-1

Бренды по названию

Популярные бренды

Tyco ACC-1, Руководство пользователя

Результаты поиска

Содержание ACC-1

Отзывы:

Похожие инструкции для ACC-1

Бренды по названию

Популярные бренды