Tyco ACC-1 Скачать руководство пользователя страница 32

Страница: 32 / 38

Appendix F of TFP1090 (07/2020)

Summary Instructions (if problems occur, consult full document)

DN150, Model DPV-1 Dry Pipe Valve with Standard Alarm Test Valve,

without Model ACC-1 Accelerator

I. Normal Conditions

• The Main Control Valve (A) is opened

and locked.

• The sprinkler system is filled with air

and is pressurized.

• The Main Drain Valve (F), and Low

Body Drain Valve (L) are closed.

• The Alarm Test Valve (E) is in the

closed position.

• The Pressure Gauge Valves (B) and

• The Pressure Switch Valve (J) is

open.

• The Air Supply Control Valve (K) is

open.

• System Air Pressure Gauge (G)

reads downstream air pressure.

• Water Supply Pressure Gauge (H)

reads the upstream water pressure.

II. Operation

When one or more sprinklers are acti-

vated, air pressure is reduced down-

stream of the Dry Pipe Valve. When the

air pressure is sufficiently reduced, the

water pressure overcomes the differen-

tial holding the Dry Pipe Valve closed

and the Dry Pipe Valve opens to per-

mit water flow into the system piping

and to be discharged from any open

sprinklers. Also, with the Dry Pipe

Valve open, water flows through the

Alarm Port at the rear of the Dry Pipe

Valve to actuate the Waterflow Pressure

Alarm Switch (M) and, as applicable,

the Water Motor Alarm.

III. Removing System From Service
Step 1.

Close the Main Control Valve

(A), and close the Air Supply Control

Valve (K).

Step 2.

Drain the system with the Main

Drain Valve (F) and by opening all auxil-

iary drain valves in the system to make

sure that cross-mains and branch lines

are drained.

IV. Placing the System Back in

Service
Step 1.

Close the auxiliary drain valves

after water ceases to discharge, and

leave the Main Drain Valve (F) open.

Step 2.

Replace the sprinklers that

have operated and the sprinklers close

to the fire.

Step 3.

Push down on the reset knob

(P) to allow the Dry Pipe Valve (D) to

re-seat.

Step 4.

Via the Air Supply Control

Valve (K), pressurize the system with

air to 0,7 bar, and then open and close

each auxiliary drain valves in the sys-

tem piping to drain any remaining water

in trapped sections. Also, partially open

the Low Body Drain Valve (L) to assure

that the riser is completely drained.

Close the Low Body Drain Valve (L) as

soon as water ceases to discharge.

Step 5.

Open the Air Supply Control

Valve (K) to restore the system to the

normal system air pressure.

Step 6.

Partially open the Main Control

Valve (A), and then slowly close the

Main Drain Valve (F).

Step 7.

Fully open the Main Control

Valve (A) and lock it open.

Step 8.

Reset the fire alarm panel and

notify the central alarm station.

V. Weekly Test

Important:

Prior to closing any valves

or activating any alarms, notify local se-

curity guards and the central alarm sta-

tion if applicable.

Step 1.

Open the Alarm Test Valve (E),

verify that the alarm signal created by

the Waterflow Pressure Alarm Switch

(M) is visible at the fire panel. If appli-

cable, check the sound of the Water

Motor Alarm — it must be clear and

steady.

Step 2.

Close the Alarm Test Valve (E),

verify that the normal supply and sys-

tem pressures are restored. If the sup-

ply pressure is below the normal, use

the instructions from the water supply

to obtain the usual pressure.

Step 3.

Close the Pressure Switch

Valve (J) and verify operation of the low

air pressure Alarm Switch (N).

Step 4.

Return the Pressure Switch

Valve (J) to the normally open position

after verifying that the alarm signal is

visible at the fire panel.

399 mm

375 mm

193 mm

480 mm

Содержание ACC-1







































Результаты поиска

Содержание ACC-1

Отзывы:

Похожие инструкции для ACC-1

Бренды по названию

Популярные бренды

Tyco ACC-1, Руководство пользователя

Результаты поиска

Содержание ACC-1

Отзывы:

Похожие инструкции для ACC-1

Бренды по названию

Популярные бренды