background image

 

Thunder i840

S2520

User’s Manual

Revision 1.01

Copyright © Tyan Computer Corporation, 2001. All rights reserved. No part of this
manual may be reproduced or translated without prior written consent from Tyan
Computer Corp.

All registered and unregistered trademarks and company names contained in this
manual are property of their respective owners including, but not limited to the fol-
lowing.

Thunder i840 S2520 is a trademark of Tyan Computer Corporation.
AMIBIOS is a trademark of American Megatrends, Inc.
Windows is a trademark of Microsoft Corporation.
IBM, PC, AT, PS/2 are trademarks of IBM Corporation.
Intel, Pentium III are registered trademarks of Intel Corporation.
Adaptec is a registered trademark of Adaptec, Inc.
QLogic, Zircon are trademarks of QLogic Corp.
ATI, Rage XL are trademarks of ATI Technologies, Inc.
Winbond is a trademark of Winbond Electronics Corp.

Information contained in this document is furnished by Tyan Computer Corpora-
tion and has been reviewed for accuracy and reliability prior to printing. Tyan
assumes no liability whatsoever, and disclaims any express or implied warranty,
relating to sale and/or use of Tyan products including liability or warranties relating
to fitness for a particular purpose or merchantability. Tyan retains the right to make
changes to product descriptions and/or specifications at any time, without notice.
In no event will Tyan be held liable for any direct or indirect, incidental or conse-
quential damage, loss of use, loss of data or other malady resulting from errors or

inaccuracies of information contained in this document.

TM

Содержание THUNDER I840



























































Отзывы: