TYAN S2927 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 88

background image

http://www.tyan.com

67

3.10 Security Menu

The system can be configured so that all users must enter a password every

time the system boots or when BIOS Setup is entered, using either the
Supervisor password or User password. The Supervisor and User passwords
activate two different levels of password security. If you select password
support, you are prompted for a one to six character password. Type the
password on the keyboard. The password does not appear on the screen when
typed. Make sure you write it down. If you forget it, you must clear CMOS and
reconfigure.

BIOS Setup Utility

Main Advanced PCI/PnP Boot

Security

Chipset Exit

Security Settings

Supervisor Password  : Not Installed
User Password   : Not Installed

Change Supervisor Password

Change User Password

Boot Sector Virus Protection [Disabled]

Install or change the
password.

←

→

Select Screen

↑↓

Select Item

+/- Change Option
F1 General Help
F10 Save and Exit
ESC Exit

Feature

Option

Description

Security Settings

Not Installed

Supervisor Password:

Installed

If the password has been set,
Installed displays. If no password
is set, Not Installed displays.

Not Installed

User Password:

Installed

If the password has been set,
Installed displays. If no password
is set, Not Installed displays.

Change Supervisor
Password

__

Selects this option to change or
install Supervisor Password.

Change User Password

__

Selects this option to change or
install User Password.

Disabled

Boot Sector Virus Protection

Enabled

When it is set to [Enabled], BIOS
will issue a virus warning
message and beep if a write to
the boot sector or the partition
table of the HDD is attempted.

«
...
65
66
67
68
69
...
»

Содержание S2927

























































































Отзывы:

Нет отзывов

Похожие инструкции для S2927

Бренд: IEI Technology Страницы: 234

Бренд: Xilinx Страницы: 14

Бренд: J&W Страницы: 28

AP0101AT2L00XPGAH3-GEVB

Бренд: ON Semiconductor Страницы: 6

Бренд: Raider Outboards Страницы: 73

BrillianX 1S/2000

Бренд: QDI Страницы: 63

Бренд: IEI Technology Страницы: 162

VVDI Mini Key Tool

Бренд: Xhorse Страницы: 17

Бренд: Supermicro Страницы: 229

Бренд: Texas Instruments Страницы: 14

Бренд: Gigabyte Страницы: 40

Бренд: Asus Страницы: 47

Бренд: TYAN Страницы: 47

Бренд: DFI-ITOX Страницы: 129

Бренд: IBASE Technology Страницы: 64

Бренд: IBASE Technology Страницы: 83

Бренд: Silicon Laboratories Страницы: 12

Бренд: Silicon Laboratories Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды