TYAN S2927 Скачать руководство пользователя страница 65

Страница: 65 / 88

http://www.tyan.com

3.9.2 Boot Device Priority

Use this screen to select options for the Boot Device Priority. Use the up and

down arrow (

) keys to select an item. Use the Plus and Minus (+/-) keys to

change the value of the selected option.

BIOS Setup Utility

Main Advanced PCI/PnP

Boot

Security Chipset Exit

Boot Device Priority

1st Boot Device

2nd Boot Device
3rd Boot Device

[xx,xxx-xxxxx:xxx]

[xx,xxx-xxxxx:xxx]
[xx,xxx-xxxxx:xxx]

Specifies the boot
sequence from the
available devices.

A device enclosed in
parenthesis has
been disabled in the
corresponding type
menu.

←

→

Select Screen

↑↓

Select Item

+/- Change Option
F1 General Help
F10 Save and Exit
ESC Exit

Feature

Option

Description

Boot Device Priority

xx,xxx-xxxxx:xxx

xx,xxx-xxxxx:xxx

1st Boot Device
2nd Boot Device
3rd Boot Device

Disabled

Settings for boot priority.
These can be customized
depending on your
preference.

Содержание S2927

























































































Результаты поиска

Содержание S2927

Отзывы:

Похожие инструкции для S2927

Бренды по названию

Популярные бренды

TYAN S2927, Руководство пользователя

Результаты поиска

Содержание S2927

Отзывы:

Похожие инструкции для S2927

Бренды по названию

Популярные бренды