manualshive.com logo in svg

TYAN GT93-B7106, Руководство сервисного инженера, Страница: 70 / 90

Поделиться
Скачать
TYAN GT93-B7106 Скачать руководство пользователя страница 70

 

http://www.tyan.com 

70

4.2   AMIBIOS Post Code (Aptio) 

 

The POST code checkpoints are the largest set of checkpoints during the BIOS 
pre-boot process.    The following table describes the type of checkpoints that may 
occur during the POST portion of the BIOS: 

Checkpoint Ranges 
Status Code Range 

Description 

0x01 – 0x0B 

SEC execution 

0x0C – 0x0F 

SEC errors 

0x10 – 0x2F 

PEI execution up to and including memory detection 

0x30 – 0x4F 

PEI execution after memory detection 

0x50 – 0x5F 

PEI errors 

0x60 – 0x8F 

DXE execution up to BDS 

0x90 – 0xCF 

BDS execution 

0xD0 – 0xDF 

DXE errors 

0xE0 – 0xE8 

S3 Resume (PEI) 

0xE9 – 0xEF 

S3 Resume errors (PEI) 

0xF0 – 0xF8 

Recovery (PEI) 

0xF9 – 0xFF 

Recovery errors (PEI) 

 

Standard Checkpoints 

SEC Phase 

Status Code 

Description 

0x00 Not 

used 

Progress Codes 

0x01 

Power on. Reset type detection (soft/hard). 

0x02 

AP initialization before microcode loading 

0x03 

North Bridge initialization before microcode loading 

0x04 

South Bridge initialization before microcode loading 

0x05 

OEM initialization before microcode loading 

0x06 Microcode 

loading 

0x07 

AP initialization after microcode loading 

0x08 

North Bridge initialization after microcode loading 

0x09 

South Bridge initialization after microcode loading 

Содержание GT93-B7106



























































































Отзывы:

Нет отзывов