manualshive.com logo in svg

TYAN GT93-B7106, Руководство сервисного инженера, Страница: 24 / 90

Поделиться
Скачать
TYAN GT93-B7106 Скачать руководство пользователя страница 24

                                                       

http://www.tyan.com

 

24

1.5.3   PSU and LAN LED Indications 

 

PSU LED Indications 

 

Power Supply Condition 

LEDs 
State 

Only Standby power and AC good or PSU in cold 
redundant state 

1Hz Blink 
green 

PW_OK (Power normal) 

Solid green 

Power supply warning events where the power 
supply continues to operate; high temp, high power, 
high current, slow fan. 

1Hz Blink 
amber 

No AC power 

Not lit 

Fault: Ambient or Hot spot occur OTP, Fan fault, 
Input AC UV, +12V output occur OVP, UVP or OCP 
(w5Vsb) 

Solid 
amber 

 

1Gbps LAN Port Indications

 

1Gbps LAN Link/Activity LED Scheme 

 

Left LED 

(Link/Activity) 

LED Color: Green 

Right LED 

(Speed) 

LED Color: Amber 

No Link 

 

OFF OFF 

10 Mbps 

Link 

Green Solid On 

OFF 

Active 

Green Blinking 

OFF 

100 Mbps 

Link 

Green Solid On 

Green Solid On 

Active 

Green Blinking 

Green Solid On 

1000 Mbps 

(1Gbps) 

Link 

Green Solid On 

Amber Solid On 

Active 

Green Blinking 

Amber Solid On 

NOTE:

 

“Left” and “Right” are viewed from the rear panel. 

Содержание GT93-B7106



























































































Отзывы:

Нет отзывов