background image

 

 

 8 

 

 

Never attempt to use a machine on materials in excess of its capability. 
 

 

Never use a machine to perform a task it has not been designed to do. 

 

 

Never operate the tractor or machine controls from any position other than from the 
driving seat, especially whilst hitching or unhitching the machine. 

 

 

Never carry out maintenance of a machine or a tractor whilst the engine is running – 
the engine should be switched off, the key removed and pocketed. 

 

 

Never leave a machine unattended in a raised position – it should be lowered to the 
ground in a safe position on a level firm site. 

 

 

Never leave a tractor with the key in or the engine running. 

 

 

Never carry out maintenance on any part or component of a machine that is raised 
unless that part or component has been properly substantially braced or supported. 

 

 

Never attempt to detect a hydraulic leak with your hand – use a piece of cardboard. 

 

 

Never allow children near to, or play on, a tractor or machine under any 
circumstances. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание TC526

























































Отзывы: