Tweco Spool gun Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 24

background image

3-8

SET-UP AND SAFE OPERATING PROCEDURES

89210007

3.02 ADJUSTING WIRE FEED PRESSURE AND SPEED

1. Use a screwdriver to adjust the wire

feed pressure. Turn the adjusting
screw clockwise to decrease, or
counterclockwise to increase pressure
on the wire feed drive rolls.

2. Adjust the “AMP“ (Wire Feed Speed)

knob on the power supply to adjust
the wire speed feed.

Direction

Result

Clockwise

Increase Speed

Counterclockwise Decrease Speed

3.03 INSTALLING THE WIRE SPOOL

1. Remove the spool cover by loosening

the cover screw by hand.

Installation and Operation

«
...
10
11
12
13
14
...
»

Содержание Spool gun

























Отзывы:

Нет отзывов

Похожие инструкции для Spool gun

Бренд: Zhongdi Страницы: 5

Бренд: Meec tools Страницы: 21

Бренд: jbc Страницы: 41

TORCH KIT 94903

Бренд: Harbor Freight Tools Страницы: 8

Бренд: jbc Страницы: 8

Бренд: jbc Страницы: 16

Quick Tools QU3205

Бренд: Bräunlich Страницы: 41

Бренд: Bräunlich Страницы: 53

Бренд: Sparkfun Electronics Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды