Tuxedo JMC9KAC-TUX Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 24

background image

１１

TP9KAC-TUX

Mar 2019

STEP 9

:

(Installing Swing Arms & Arm Restraints)

1. Install the swing arms on the carriages using the

included 1-1/2

” swing arm pins.

Note: (Asymmetric Lifts – the short, asymmetric

swing arms are designed for front vehicle

placement, with the long, asymmetric arms for

rear vehicle placement.

2. Install arm restraint mechanisms to each swing arm, as shown below in

(Fig. 13)

.

3. Check for proper engagement for the arm restraints as the gear rack should fully engage the gear on

the arm.

Fig. 13

SAFETY NOTICE!

«
...
9
10
11
12
13
...
»

Содержание JMC9KAC-TUX

























Отзывы:

Нет отзывов

Похожие инструкции для JMC9KAC-TUX

Бренд: Fandis Страницы: 8

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

Бренд: ICP DAS USA Страницы: 7

I-2533CS Series

Бренд: ICP DAS USA Страницы: 8

Бренд: rav Страницы: 120

Бренд: hotset Страницы: 2

Бренд: Equalizer Страницы: 26

Markoprint iJET

Бренд: Weber Страницы: 127

Бренд: W&T Страницы: 72

CIRCOtransfer 30 E

Бренд: wagner solar Страницы: 32

WAGO-I/O-SYSTEM 750-424

Бренд: WAGO Страницы: 12

Бренд: Bame Страницы: 12

iNELS Air AirIM-100S

Бренд: Elko Страницы: 8

UVL Series NUVL604XA

Бренд: Braun Corporation Страницы: 38

Бренд: FY-TECH Страницы: 34

ACCOLIFT series

Бренд: ACCO Brands Страницы: 140

Бренд: ubbink Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды