manualshive.com logo in svg

Tuthill KINNEY KMBD Series, Инструкция по установке, эксплуатации, обслуживанию и ремонту

Поделиться
Скачать
Tuthill KINNEY KMBD Series Скачать руководство пользователя страница 31

IMPORTANT

All mechanical vacuum boosters manufactured by Tuthill Vacuum & Blower Systems are date coded at time of shipment. In order to 

assure you of the full benefits of the product warranty, please complete, tear out and return the product registration card below, or 

you can visit our product registration web page at:

http://www.tuthillvacuumblower.com/index.cfm/contact-us/product-registration/

OPERATING DATA

It is to the user’s advantage to have the requested data filled in below and available in the event a problem should develop in the 

blower or the system. This information is also helpful when ordering spare parts.

Model No.  

     

V-Belt Size:    

 

   Length:   

 

Serial No.  

     

Type of Lubrication:  

     

 

      

Startup Date  

     

       

 

Pump RPM  

     

Operating Vacuum      

 

Pump Sheave Diameter:   

    

Any other special accessories supplied or in use:

Motor Sheave Diameter:   

    

       

 

Motor RPM   

 

 HP   

 

       

 

NOTES:   

             

               

               

               

               

              

 

IMPORTANT

All KINNEY

®

 vacuum pumps manufactured by Tuthill Vacuum & Blower Systems are date coded at time 

of shipment. In order to assure you of the full benefits of the product warranty, please complete, tear out 

and return this product registration card.

Company ________________________________________________________________

Location__________________________________________________________________

  

City 

State/Province 

 

ZIP/Postal Code 

Country

PLEASE CHECK ONE

Vacuum Furnace   

Vacuum Coating   

Pharmaceutical  

 

Semiconductor/Electronics 

Food/Meat Packing  

Gas/Petrochemical  

Other  _________________________

Telephone : 

     (     )_____________________

E-mail:   

     _________________________

Model:   

     _________________________

Serial Number: 

     _________________________

Date of Purchase:  _________________________

Date of Startup:       _________________________

Содержание KINNEY KMBD Series

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды