Tuthill KINNEY KMBD Series Скачать руководство пользователя страница 27

Страница: 27 / 32

MIN R

- A -

.002 (.05)

KMBD-540 AND KMBD-720

MECHANICAL SEAL TOOL

T11549

Ø 2.436

± .001

.125

.002

Ø 2.103

± .010

Ø 2.243

± .001

30°

.08 × 15°

.187

4.00

MATL P/N: CR1215RO-0250 × 4.25 (88.9) LG

MATL: COLD ROLLED STEEL BAR, Ø 2.50 (63.5) OD × 4.25 (107.95) LG

TOLERANCES

ENGLISH

.XX = ± .01

.XXX = ± .005

CHAMFERS = ± 2°

3.25

(82.6)

.25

(6.3)

MIN R

Ø 1.62

(41.1)

Ø 1.872 ± .001

(47.55 ± .03)

.06 × 45°

(1.5)

.05 × 30°

(1.0)

MATL P/N: CR1018R0-0200 × 3.50 (88.9) LG

MATL: COLD ROLLED 1018, 2.00 (50) OD × 3.50 (90) LONG

KMBD-240 AND KMBD-400

SEAL PRESSING TOOL

T32018-1

Ø 2.50

(63.5)

Ø 2.25

(57.1)

MIN R

Ø 1.885 ± .001

(47.55 ± .03)

Ø 2.044 ± .001

(51.90 ± .03)

.50

(12.7)

.74

(18.8)

1.50

(38.1)

KMBD-240 AND KMBD-400

SEAL PRESSING TOOL

T32018-2

MATL P/N: CR1026T0-250050 × 1.75 (44.5) LG

MATL: COLD ROLLED 1026 TUBE, 2.50 (65)

OD × .50 (15) WALL × 1.75 (45) LONG

TOOL ASSEMBLY FOR END PLATE LAB SEAL, END PLATE

LIP SEAL AND END PLATE MECHANICAL SEAL INSTALLATION

TOLERANCES

ENGLISH

.XX = ± .01

.XXX = ± .005

ANGULAR = ± .005

METRIC

.XX = ± .03

.XXX = ± .05

ANGULAR = °

NOTE:

DIMENSIONS SHOWN IN INCHES

DIMENSIONS IN ( ) ARE IN UNITS OF MILLIMETERS

TOOLS T32018-1 & T32018-2 ARE USED TO INSTALL

MECHANICAL SEAL, LABRYINTH SEAL AND LIP SEAL

USED ON MODELS KMBD-240 AND 400 ROTOR SHAFTS.

Содержание KINNEY KMBD Series

































Результаты поиска

Содержание KINNEY KMBD Series

Отзывы:

Бренды по названию

Популярные бренды

Tuthill KINNEY KMBD Series, Инструкция по установке, эксплуатации, обслуживанию и ремонту

Результаты поиска

Содержание KINNEY KMBD Series

Отзывы:

Бренды по названию

Популярные бренды