Turnigy B405 Скачать руководство пользователя страница 13

Starting Charge 

(

Continued

)

Care and Handling of LiPo, Li-Ion and LiFe Batteries (Continued)

Starting Charge 

(

Continued

)

Warning and Error Messages

NEVER

 charge LiPo, Li-Ion or LiFe batteries at currents greater than the maximum 

rated current as specified by the battery

s manufacturer

.

NEVER

 allow LiPo cells to come into contact with moisture or water at any time.

NEVER

 

allow the electrolyte from LiPo, Li-Ion or LiFe batteries to get in the eyes 

or on the skin 

wash affected areas immediately if they come in contact with the 

electrolyte and contact your doctor

.

NEVER

 attempt to use the charger’s NiCd and NiMH functions for LiPo or Li-Ion 

batteries

.

ALWAYS

 keep lithium batteries away from children.

NEVER

 attempt to charge a lithium battery that is swollen or where one cell is 

under 3

.

0V

NEVER

 allow LiPo, Li-Ion or LiFe cells to overheat at any time as they can become 

physicaly damaged and could possibly explode or catch fire

If a battery becomes 

overheated 

(

over 140

°

F

60

°

C

), 

disconnect it from the charger 

IMMEDIATELY

.

NEVER

 continue to charge LiPo, Li-Ion or LiFe batteries if the charger fails to 

recognise a full charge

LiPo and LiFe cells which swell or emit smoke may be in 

overcharge condition and should be disconnected from the charger immediately

.

NEVER

 set the charger’s LiPo/Li-Ion or LiFe battery voltage settings to a voltage 

that is HIGHER than the nominal rating of the battery itself

as such cells cannot 

handle overcharging in any way

.

The  B405   incorporates  various  functions  to  protect  and  monitor  the  system

,

to verify

 

functions  and  the  state of  its  electronics

.  

In  the case of an error

the screen will 

display the cause of the error

This is also warned via an audible sound

.

The DC input voltage is below 10

.

0V or exceeds 18V DC

Make sure 

that the input voltage is within this range

.

A battery is not connected to the output

Make sure a good connection 

exists between the battery and charger and re

-

try

.

• 

• 

• 

• 

• 

• 
• 
• 

• 

-  13  -

Содержание B405

















Отзывы: