background image

15

85874 & 85875 Rev B

TURFCO T3000i SERIES APPLICATOR

LOCKING KNOB

SPREADER GATE

OPEN/CLOSE CONTROL HANDLE

VARI-RATE

ADJUSTABLE

GATE STOP

FIGURE 10

SPREAD TRIM BORDER PATROL

ON

SPREADER SPINNER

WHEEL SPEED

CONTROL

OP85872-14

OFF

NARROW

WIDE

OPEN

CLOSE

60%

FULL

4

3

OPERATION

5. SPINNER WHEEL

 (See Figure 8 and 9) -

 

The 

Spinner  Wheel  broadcasts  the  material  from 

the hopper. The speed of the spinner wheel is 

controlled by the Spinner Speed Control.

6. SPINNER SPEED CONTROL 

(See Figure 8 and 

10) -

  

The Spinner Speed Control lever allows the 

operator to speed up or slow down the spinner 

wheel to vary the spread pattern width. Push the 

Spinner  Speed  Control  lever  full  ahead  for  full 

application width and pull back for the narrow or 

trim width. A slower spinner wheel speed results 

in a narrower spread width (about 7 foot wide) 

for use in narrow spots,  trimming, and to avoid 

putting product where it is not wanted.
Note: The Spinner Speed Control lever should 

only be moved when the engine is running. No 

damage will occur if the lever is moved while the 

engine is not running, it is just better for the belts 

and pulley to be moving when activated.

7.  SPREADER  GATE  OPEN/CLOSE  CONTROL 

(See  Figure  10)  - 

The  Spreader  Gate  Open/

Close  Control  handle  controls  the  opening  of 

the spreader gate. Push forward to the open the 

gate or pull back to close.

8.  VARI-RATE  ADJUSTABLE  GATE  STOP 

(

See 

Figure 10) - 

Vari-Rate Adjustable Gate Stop is 

located  next  to  the  spreader  gate  handle.  The 

stop  will  limit  the  movement  of  the  spreader 

gate  control  handle.  This  causes  the  spreader 

gate to stop at a preset opening size that is less 

than 100% open (opening must be preset during 

calibration).  To  use  the  Vari-Rate  stop,  simply 

push the lever in as you open the gate. The lever 

will snap in to a more vertical position and stop at 

the gate stop. To bypass the stop, tip the control 

out as you move it forward to open the gate and 

the handle will miss the stop allowing the gate to 

fully open.
The Vari-Rate Adjustment Gate Stop should only 

be  set  by  the  person  calibrating  the  spreader. 

This  should  never  be  done  in  the  field  and 

should  be  changed  whenever  the  calibrated 

rate is changed. 

The exact setting for the Vari-

Rate should only be set by licensed persons. 

Refer to the spreader calibration section in this 

manual.

9. SPREAD TRIM BORDER PATROL 

(See Figure 

8  and  10)  - 

The  Spread  Trim  Border  Patrol 

deflector  is  on  the  left  side  of  the  hopper  and 

is  operated  by  a  lever  on  the  left  side  of  the 

operators panel. The Border Patrol deflector is 

operated by pushing the lever down for trim and 

up for full width application.

Содержание T3000i 85874





















Отзывы: