turbofan Moffat E27 Скачать руководство пользователя страница 37

Страница: 37 / 37

-38-

Revision 1/F3563

C. Stacking the Ovens

(Refer figure A.2)

1. With two persons, lift the top oven onto the bottom oven and position slightly forward so that

the double stack front engages with the lintel support on the bottom oven, then slide the top
oven back until the double stack rear locates over the bottom oven.

2. Secure double stack rear to bottom unit with four screws. Secure the double stack front to the

lintel support of the bottom unit with three screws.

3. Remove the rear cover panel from the top unit. Fit the vent pipe to the vent duct then

secure pipe to the rear panel of the top unit using the saddle clamp and two screws.

4. Using pliers or similar, knock out the notches at the top and bottom of the rear cover panel

that allow for the vent pipe. Refit the rear cover panel to the top unit.

Figure A.2

Содержание Moffat E27






































Результаты поиска

Содержание Moffat E27

Отзывы:

Похожие инструкции для Moffat E27

Бренды по названию

Популярные бренды

turbofan Moffat E27, Руководство по обслуживанию

Результаты поиска

Содержание Moffat E27

Отзывы:

Похожие инструкции для Moffat E27

Бренды по названию

Популярные бренды