background image

17

USE  AND  CARE  INSTRUCTIONS

CORRECT USE OF LP GAS TANK

The  LP  Gas  tank  must  be  constructed  and  marked  in
accordance  with  the  Specifications  for  LP-Gas  Cylinders
of the U.S.  Department of  Transportation (D.O.T.)  or the
National Standard of Canada, CAN/CSA-B339, Cylinders,
Spheres  and  Tubes  for  Transportation  of  Dangerous
Goods  and  Commission;  as  applicable.

The LP Gas tank must have a shutoff valve, terminating
in an LP Gas supply tank valve outlet, that is compatible
with  a Type  1 tank  connection  device. The  LP Gas  tank
must  also  have  a  safety  relief  device  that  has  a  direct
connection  with  the  vapor  space  of  the  tank.

The  tank  supply  system  must  be  arranged  for  vapor
withdrawal.

The  LP  Gas tank must  have  a  collar  to protect  the  tank
valve.

Never  connect  an  unregulated  LP  gas  tank  to  your  gas
grill.  The  gas  regulator  assembly  supplied  with  your  gas
grill  is  adjusted  to  have  an  outlet  pressure  of  11"  water
column  (W.C.)  for  connection  to  an  LP  gas  tank.  Only
use the regulator  and  hose  assembly  supplied  with your
gas  grill.  Replacement  hose  and  regulator  assembly
must  be  identical  to  those  listed  in  the  parts  list  of  this
Operator's  Manual  as  specified  by  Barbeques  Galores.

Have your LP Gas dealer check the relief valve after every
filling  to  ensure  it  remains  free  of  defects.

Always  keep  LP  Gas  tank  in  upright  position.

Do not subject the LP Gas tank to excessive heat.

Never  store  an  LP  Gas  tank  indoors.  If  you  store  your
gas  grill  in  the  garage  always  disconnect  the  LP  Gas
tank  first  and  store  it  safely  outside.

LP  Gas  tanks  must  be  stored  outdoors  in  a  well-
ventilated  area  and  out  of  the  reach  of  children.

Disconnected  LP  Gas  tanks  must  not  be  stored  in  a
building,  garage  or  any  other  enclosed  area.

The  regulator  and  hose  assembly  can  be  seen  by
opening  the cabinet  door  and  must  be  inspected  before
each use of the grill. If the hose is damaged in any way,
it  must  be  replaced  prior  to  using  the  grill  again.

Any  attempt  to  convert  the  grill  from  one  fuel  type  to
another  is  extremely  hazardous  and  will  void  the  war-
ranty.

Never  light  your  gas  grill  with  the  lid  closed  or  before
checking to ensure the burner tubes are fully seated over
the  gas  valve  orifices.

Never  allow  children  to  operate  your  grill.  Do  not  allow
children  or pets to  play near  your grill. Always  supervise
children  and  pets  if  they  are  in  the  vicinity  of  the  unit.

Never 

use  charcoal  or  lighter  fluid  in  this  grill.

Use  of  alcohol,  prescription  or  non-prescription  drugs
can  impair  your  ability  to  properly  assemble  and
safely  operate  your  grill.

Keep fire  extinguisher readily accessible. In the event
of  a  oil/grease  fire,  do  not  attempt  to  extinguish  with
water.  Use  type  B  extinguisher  or  smother  with  dirt,
sand  or  baking  soda.
In  the  event  of  rain,  turn  off  the  burners  and  gas
supply.  Wait  for  the  grill  to  cool,  and  then  place  a
cover  on  it.
Use  your  grill  on  a  level,  stable  surface  in  an  area
clear  of  combustible  materials.

LP Gas grill models are designed for use with a standard
20  lb.  Liquid  Propane  Gas  (LP  Gas)  tank  (sold  sepa-
rately). 

Never 

connect  your  gas  grill  to  an  LP  Gas  tank

that  exceeds  this  capacity.  A  tank  of  approximately  12
inches in diameter by 18-1/2 inches high is the maximum
size LP  Gas tank  to use. 

You  must use  an 

"

OPD"  gas

tank  which  offers  a  listed  Overfill

 

Prevention  Device.

This  safety  feature  prevents  tank  from  being  overfilled
which  can  cause  a  malfunction  of  the  LP  Gas  tank.

Do  not  leave  grill  unattended  when  in  use.
Do  not  move  the  appliance  when  in  use.
Allow  the  grill  to  cool  before  moving  or  storing.
Do  not  use  your  grill  as  a  heater.
Never  use  your  gas  grill  on  a  balcony,  deck,  patio
above  the  ground  floor  of  your  home.
This  grill  is  not  intended  to  be  installed  in  or  on
recreational  vehicles  and/or  boats.
The  grill  is  not  intended  for  commercial  use.

!

Do  not  store  a  spare  LP-Gas  tank  under  or  near
this  appliance.
Never  fill  the  tank  beyond  80  percent  full;  and
If  the  information  in  "(a)"  and  "(b)"  is  not  followed
exactly,  a  fire  causing  death  or  serious  injury  may
occur.

A.

B.
C.

  WARNING

!

Refer  to  the  this  table  when  designing  the  island  unit
for the 

BTE3221BLP/NG & BTE3821BLP/NG

. Side* and Rear*

show the minimum amount of distance the unit must be
from combustibles (ex. Vinyl or wood siding, fences and
overhangs) or sources of ignition (ex. Pilot lights on water
heaters and live electrical appliances). Height* shows the
minimum height the island unit must be starting from the
ground up.

 

7" minimum clearance
from cutout (for lid)

Side*

Depth

Height

Width

Non-combustible
Construction

Rear*

Height*

Model

Height

Width

Depth

Side* Rear* Height*

BTE3221B

LP/NG

9-1/2" 30-1/2" 19-3/4"

36"

36"

29"

BTE3821B

LP/NG

9-1/2"

38"

19-3/4"

36"

36"

29"

!

  WARNING

!

Содержание BTE3221ALP



































Отзывы: