background image

 

 

M a n u a l   P / N   6 4 8 5 - 0 0 5 ,   RE V   C

PG E

                                         

  

Page 

5

 

 

4.

 

Hold the smoke hood in front of you, stretching the neck seal open with both hands 

(Figure 3)

 

Figure 3: Neck seal stretched open (Essex standard configuration shown) 

5.

 

Pull the smoke hood over your head, adjusting in place for comfort. 

6.

 

Once you are wearing the hood, follow your standard training procedure. 

7.

 

After your training exercise is complete, bend down and remove the device by grabbing 

the back of the hood and pulling forwards off your head. 

3.2.

 

Disinfection 

The neck seal and facial contact area in the front of the hood should be disinfected with alcohol 

between uses in order to ensure the health of the trainees.  

3.3.

 

Rearming 

The PBE should be rearmed in order to prepare for the next use. 

For the pull ball configuration, attach one 

clip to each simulated oxygen generator 

(Figure 2). 

For the Essex standard configuration, attach 

the clips to the simulated oxygen generator 

on the opposite side of the PBE (Figure 2). 

Attach the clips as shown below (Figure 4)

 

Содержание 6485-001












Отзывы: