Tufline BCP1816 Скачать руководство пользователя страница 15

levers can cause equipment to drop or rotate 

unexpectedly and cause severe injury or death.

• Service work does not require going under-

neath.

• Read Manual for service instructions or have

service performed by a qualified dealer.

• Stop tractor and implement immediately upon

striking an obstruction. Turn off engine, remove 

key, inspect, and repair any damage before 

resuming operation.

• Always wear relatively tight and belted cloth-

ing to avoid entanglement in moving parts. 

Wear sturdy, rough-soled work shoes and pro-

tective equipment for eyes, hair, hands, hearing 

and head.

Owner/Operator Pre-Operation Checklist

(Owner’s/Operator’s Responsibility)

____ Review and follow all safety rules and 

safety decal instructions on page 6 through 

page 8.

____ Check that equipment is properly and 

securely attached to tractor.

____ Check that all safety decals are installed 

and in good condition. Replace if damaged.

____ Check that all hardware is properly 

installed and secured.

____ Do not allow riders.

____ Make sure tractor ROPS or ROPS CAB

and seat belt are in good condition. Keep seat 

belt securely fastened during operation.

___ After day of operation, check all hardware. 

Retighten if needed. Please see Bolt Torque 

Chart (page 33) for proper torque information.

 Operation 12

Safety is a primary concern in the design and 

manufacture of our products. Unfortunately, our 

efforts to provide safe equipment can be wiped 

out by an operator’s single careless act.
In addition to the design and configuration of 

equipment, hazard control and accident pre-

vention are dependent upon the awareness, 

concern, judgement and proper training of per-

sonnel involved in the operation, transport, 

maintenance and storage of equipment.

It has been said “The best safety device is an 

informed, careful operator. ”We ask you to be 

that kind of operator.

The operator is responsible for the safe opera-

tion of this equipment. The operator must be 

properly trained. Operators should be familiar 

with the equipment, the tractor and all safety 

practices before starting operation. Read the 

safety rules and safety decals on pages 5-7.

• Power unit must be equipped with ROPS or 

ROPS cab and seat belt. Keep seat belt 

securely fastened. Falling off power unit can 

result in death from being run over or crushed.

Keep foldable ROPS systems in “locked up” 

position at all times.

• Never allow children or untrained persons to 

operate equipment.

• Keep bystanders away from equipment.

• NEVER GO UNDERNEATH EQUIPMENT.

Never place any part of the body underneath 

equipment or between moveable parts even 

when the engine has been turned off. Hydraulic 

system leak down, hydraulic system failures, 

mechanical failures, or movement of control 

OPERATION

WARNING

Содержание BCP1816







































Отзывы: