TG-11L Leg Press (Option)
2
Owners’ Manual: Assembly Instructions
FIG. A
Attach the TG-11L to the TG-150, as shown above, and
secure it into using two Hex Head Cap Screws 3/8-16 X 3 3/4 (#15), four
Flat Washers SAE 3/8 (#23) and two Nylon Insert Jam Lock Nuts 3/8-16
(#25). When installing the TG-11L you will receive a new cable, the
Main
Cable (#16-Labeled with tape TG-150)
. This
Main Cable (#16-Labeled
with tape TG-150)
will replace the existing cable you are using for the
Leg Extension station on the TG-150. This new
Main Cable (#16-Labeled
with tape TG-150)
will now be used for the Leg Extension and the Leg
FIG. 2
Attach three Nylon Pulleys 4 1/2 Rd. (#30) ,as shown above.
Attach two of the Nylon Pulleys 4 1/2 Rd. (#30) to the brackets located
on the
Fulcrum (#1)
and then one on the
Main Frame (#2)
. Secure all
Nylon Pulleys 4 1/2 Rd. (#30) into place using three Hex Head Cap
Screws 3/8-16 X 1 3/4 (#18), six Flat Washers SAE 3/8 (#23) and three
Nylon Insert Jam Lock Nuts 3/8-16 (#25). Next, insert the
Small Axle
(#9)
into the
Main Frame (#2)
. Then mount the
Fulcrum (#1)
onto the
front of the
Main Frame (#2)
and secure it into place using one Hex
Head Cap Screw 1/2-13 X 5 1/2 (#14), two Flat Washers SAE 1/2 (#22)
and one Nylon Insert Jam Lock Nut 1/2-13 (#20) . Next, insert the
Foot
Plate (#4)
onto the
Fulcrum (#1)
, as shown above, with the
Large Axle
(#5)
and secure it into place using two Set Screws 3/8-16 X 1/2 (#12).
Note
: It is recommended to lubricate the axles using a multi-purpose
Fig. 3
Note
: Before routing the cable, locate the
Main Cable (#16-
Labeled with tape TG-150)
or the
Main Cable (#31-Labeled with
tape TG-250)
. The label on the cable will determine which cable is
needed for either the TG-150 or the TG-250.
Route the
Main Cable
(#31 or #16)
, as illustrated above, beginning at the TG-150 or TG-250
and finishing at the
Fulcrum (#1)
mounting bracket. Secure the
Main
Cable (#31 or #16)
to the
Fulcrum (#1)
mounting bracket using one
Hex Head Cap Screw 1/2-13 X 1 (#21), two Flat Washers SAE 1/2
(#22) and one Nylon Insert Jam Lock Nut 1/2-13 (#20).
Note
: Use
Fig.
A
and
Fig. B
and your TG-150 Or TG-250 Instruction Manual for
further clarification of the this cable routing.
FIG. B
Attach the TG-11L to the TG-250, as shown above, and
secure it into place using two Hex Head Cap Screws 3/8-16 X 3 3/4 (#15),
four Flat Washers SAE 3/8 (#23) and two Nylon Insert Jam Lock Nuts 3/8
16 (#25). When installing the TG-11L you will receive a new cable,
Main
Cable (#31-Labeled with tape TG-250)
. This
Main Cable (#31-Labeled
with tape TG-250)
will replace the existing cable you are using for the
Low Row station on the TG-250. This new
Main Cable (#31-Labeled with
tape TG-250)
will now be used for the Low Row and the Leg Press
Note:
Some Parts Not
Shown or cut away for
clarity
Fig. B
TG-11L to TG-250
Cable Routing Diagram
Fig. A
TG-11L to TG-150
Cable Routing Diagram
