Tuff Birds Micro BEE Скачать руководство пользователя страница 5

Страница: 5 / 6

BUILD INSTRUCTIONS

Tuff Birds

Super Tough Wings & Planes

13 Wiring Diagram

Motor

ESC

BATTERY

Servo 2

Servo 1

PROP

LEFT

RIGHT

Left Elevon Moves Up | Right Elevon Moves Down

Plane will Roll/Turn Right

LEFT

RIGHT

Left Elevon Moves Down | Right Elevon Moves Up

LEFT AILERON

RIGHT AILERON

Down Elevator

LEFT

RIGHT

Both Elevons Move down

Plane will Nose Down / Dive

Plane will Nose UP / Climb

UP Elevator

LEFT

RIGHT

Both Elevons Move UP

CH 1

CH 2

CH 3

FPV Gear

14 Elevon Mixing

Use the supplied throw gauge to set the throws
of Elevons. Start with the recommendation and
then you may adjust later to suit your flying
style.
Check all linkages to be tight, and slop-free.
Double check the CG balance point.

15 Final Checks

Elevon Throws

Throw Gauge

Elevon at Neutral

Micro BEE

600MM Flying Wing

Plane will Roll/Turn Left

Ver 1.0 12 May 2018

Содержание Micro BEE







Результаты поиска

Содержание Micro BEE

Отзывы:

Бренды по названию

Популярные бренды

Tuff Birds Micro BEE, Инструкция пользователя

Результаты поиска

Содержание Micro BEE

Отзывы:

Бренды по названию

Популярные бренды