Tucson T-238 Скачать руководство пользователя страница 6

 

T-238 Assembly Manual 

Rev. 1 February 2001 

Page 6 of 11 

[  ] U2 7805 
 
[  ] Solder and clip the leads (3 total) 
 

LCD Module

 

Now you will prepare the LCD module for connection to the 
T-238 PCB.  The LCD connects to the PCB via a flat 
ribbon cable. 
 
[  ] Carefully remove the LCD module from its protective 
packaging. 
 
You will be soldering a 1x16-pin male header to the LCD.  
During this time you need to protect the LCD screen from 
splatter while soldering. 
 
[  ] Cover the LCD screen while soldering. 
 
[  ] A 1x17-pin male header is supplied in the kit.  Carefully 
trim 1 pin off one end of the header to make a 1x16-pin 
header. 
 
[  ] Position the 1x16-pin male header to the rear of the 
LCD in the holes on the top of the display.  These are the 
holes labeled with a 1 on one end and a 16 on the other. 
 
[  ] Solder the 1x16-pin male header with pins facing to the 
rear of the LCD module and in holes 1 through 16.   
 

NOTE  –

J8 on the PCB is an alternate connection for 

powering the LED backlight on the LCD.  There will be a 
red and black wire, a polarized Molex plug housing, and 
two pins remaining.  These are for LCD displays that  do 
not have a 16-pin header but rather a 14-pin header.  Pins 
15 and 16 supply power to the LED backlight.  The LCD 
display supplied with your kit has a 16-pin header.  You 
may save these parts for any future modification on your T-
238. 
 
That completes the assembly of the LCD module cables.  
Set them aside for now.  The LCD module will be 
connected to the PCB after a few voltage  checks are 
completed in the next section. 
 

Almost done 

At this point, these should be the only items left  
 

NOTE:

 Keep U3 and U4 in the antistatic foam 

 
[  ] U3 MC68HC908GP32  
[  ] U4 MAX23 
 
[  ] 2.1 mm Coaxial Plug  
 
You are almost finished assembling the PCB.  Next you will 
do some final checks before applying power. 
 

Содержание T-238













Отзывы: