background image

A TUCKER AUTO-MATION HOLDINGS COMPANY

WWW.

TUCKERZAP.COM

Toll Free:

 1-855-8 TUCKER 

Tel:

 412-823-2537 

Fax:

 412-816-1862

Technical Support:

 1-888-467-5751

Email:

 [email protected]

Contact Information:

Tucker Auto-Mation ZAP Supply

,

 LLC

Location:

11075 Parker Drive

Irwin, PA 15642

Tucker ZAP PATENT NUMBER / TITLE / REGISTRATION DATE:

 

USA 8,182,381

 | Drive arrangement | May 22, 2012

USA 8,115,438

 | Aperture closure member control arrangements | Feb. 14, 2012

USA 8,033,374

 | Drive arrangement | Oct. 11, 2011

USA 7,633,253

 | Control and monitoring arrangements for an aperture closure member | Dec. 15, 2009

USA 7,437,971

 | Drive arrangement | Oct. 21, 2008

USA 7,333,308

 | Control arrangement | Feb. 19, 2008

USA 7,005,884

 | Monitoring apparatus for monitoring electrical drive current for an electric motor | Feb. 28, 2006

USA 6,188,198

 | Aperture closures | Feb. 13, 2001

Mexico 243645

 | Aparato de monitoreo | Feb. 6, 2007

Canada 2445152

 | Monitoring apparatus | June 25, 2013

Canada 2440772

 | Control arrangement | June 21, 2011

Canada 2560530

 | Drive arrangement | May 21, 2013

Canada 2641641

 | Aperture closures | April 26, 2011

Canada 2445123 

| Drive arrangement | Feb. 16, 2010

Canada 2338191

 | Aperture closures | Dec. 30, 2008

USER OPERATING INSTRUCTIONS

ZAP 800 and 8800 Series 3 

Commercial Door Shaft-Mounted Motor Operators

 

920.1035.00_USER OPERATING INSTRUCTIONS

Содержание 8800









Отзывы: