Tsurumi Pump OM Скачать руководство пользователя страница 4

-3-

 PRECAUTIONS DURING MAINTENANCE AND INSPECTION

CAUTION

WARNING

Absolutely turn off the power 

supply or disconnect the plug 

before starting maintenance or 

inspection. Do not work with wet 

hands. 

Failure to observe these 

cautions may lead to electrical 

shock or injury.

After reassembly, always perform a test operation before resuming use of the prod-

uct. 

Improper assembly can result in electrical leakage, electrical shock, fire, 

or water leakage .

In case any abnormality (excessive 

vibration, unusual noise or odor) is 

found in the operation, turn the 

power off immediately and consult 

with the dealer where it was 

purchased or Tsurumi representa-

tive. 

Continuing to operate the 

product under abnormal condi-

tions may result in electrical 

shock, fire, or water leakage.

Do not disassemble or repair any 

parts other than those designated 

in the operation manual. If repairs 

are necessary in any other than 

the designated parts, consult with 

the dealer where it was 

purchased or Tsurumi representa-

tive. 

Improper repairs can 

result in electrical leakage, 

electrical shock, fire, or water 

leakage.

Test 

operation

STOP

OFF

OFF

 PRECAUTION TO POWER OUTAGE

In case of power outage, turn off the power supply. 

The product will resume 

operation when the power is restored, which presents serious danger to 

people in the vicinity.

WARNING

power 

outage

OFF

CAUTION

Do not allow foreign objects (metal 

objects such as pins or wires) to 

enter the suction inlet of the pump. 

Failure to observe this caution 

could cause it to malfunction or 

to operate abnormally, which 

may lead to electrical leakage or 

electrical shock.

Do not use the product for hot or 

warm liquid over 40℃, as 

doing so 

will damage the product, which 

may lead to electrical leakage or 

electrical shock.

When the product will not be used 

for an extended period, be sure to 

turn off the power supply (earth 

leakage circuit breaker, etc.). 

Deterioration of the insulation 

may lead to electrical leakage, 

electrical shock, or fire.

OFF

 OTHER PRECAUTION

CAUTION

Never  use  the  product  for  potable  water. 

It  may  present  a  danger  to  human 

health.

Potable 

Water

Содержание OM
















Отзывы: