Tsubaki TSM4000H2, Инструкция по эксплуатации, Страница: 18 / 28

- 17 -
Parameter
(Default data is shown.)
Data Description
MIN
(Shock Time:
Minimum)
[Time required for detection and output]
・ Motor power supply frequency: 50 Hz or more
･･･ Approx. 50 ms
・ Motor power supply frequency: Less than 50 Hz
･･･ 2 Approx. 10 ms
(Example: 40 Hz ･････ 60 ms)
0.1 to 10.0 s
(Minimum
setting
increment: 0.1 s)
・
Period between the instant when the load ratio
reaches or exceeds the setting value and the
instant when the relay output is activated.
・ If the load ratio goes below the value of
7:High2 Level within the specified period,
the relay output is not activated.
(1)Self-Hold
(Self holding)
The status of the relay output is retained.
The status is reset by pressing the RESET
key or by an input to the [RST] terminal.
(2)Auto-Reset
(Automatic reset)
The status is reset one second after the relay
output condition is cleared.
Number of moving
average
sampling times (1) QUICK
(2) NORMAL
(3) SLOW
・ Set the response time for electric power
detection.
The moving average of the sampling values
obtained at every 20 ms (*) is calculated and
treated as effective data.
There are three options to set the number of
sampling values used for the average
calculation.
・ QUICK: Set this option when quick response
is required. The data of one sampling value
is regarded as effective data (20 ms).
・ NORMAL: Use this setting for normal
operation. The average of five sampling
values is regarded as effective data (100 ms).
・ SLOW: Set this option when you want to
reduce display fluctuation. The average of 20
sampling values is regarded as effective data
(400 ms).
* The sampling cycle is fixed to 20 ms at 50
Hz or higher frequencies, and to one cycle at
less than 50 Hz.
(1)On
When the Shock Monitor detects the change in
the motor power supply frequency and the
frequency continues changing at the rate of 4
Hz or higher per second, inhibit function is
activated regardless of the inhibit time setting.
(2)Off
The Auto Inhibit is disabled.
Reference value writing
method
(1)Interval
After the setting value of 4: HIGH1 Level is
added to the load level obtained when the
Start Time finishes and the sum is written as
the monitoring level, the previous monitoring
level is overwritten at the intervals specified
for 13: Interval Time.
(2)X1
After the setting value of 4: HIGH1 Level is
added to the load level obtained when the
Start Time finishes and the sum is written as
the monitoring level, the previous monitoring
level is overwritten when the section between
external input terminal X1 and CM is
short-circuited.
8
8 8
8 : S h o c k T i m e
: S h o c k T i m e : S h o c k T i m e
: S h o c k T i m e
H
H H
H 2
2 2
2 1 . 0 s
1 . 0 s 1 . 0 s
1 . 0 s
SET
… Make the set data
effective.
▲…Increment the setting value.
▼…Decrement the setting value.
9 9 9 9 : O u t p u t R e l a y : O u t p u t R e l a y : O u t p u t R e l a y : O u t p u t R e l a y
H
H H
H 2
2 2
2 ( 1 ) S e l f
( 1 ) S e l f ( 1 ) S e l f
( 1 ) S e l f ---- H o l d
H o l d H o l d
H o l d
SET
… Make the set data
effective .
▲
▼ … S e l e c t d a t a .
1
1 1
1 0
0 0
0 :::: R e s p o n s e
R e s p o n s e R e s p o n s e
R e s p o n s e
( 2 ) N O R M A L
( 2 ) N O R M A L ( 2 ) N O R M A L
( 2 ) N O R M A L
1
1 1
1 1
1 1
1 : A u t o I n h i b i t
: A u t o I n h i b i t : A u t o I n h i b i t
: A u t o I n h i b i t
( 2 ) O f f ( 2 ) O f f ( 2 ) O f f ( 2 ) O f f
▲
▼
… S e l e c t d a t a .
SET
… Make the set data
effective .
C
o
n
te
n
ts
U
s
a
g
e
/N
a
m
e
s
S
a
fe
ty
In
st
al
la
tio
n
/W
ir
in
g
T
er
m
in
a
ls
C
on
n
ec
tio
n
O
p
e
r
a
ti
o
n
O
p
e
r
a
ti
o
n
O
p
e
r
a
ti
o
n
O
p
e
r
a
ti
o
n
M
ai
n
te
n
an
ce
/In
sp
ec
tio
n
Sp
ec
ifi
ca
tio
ns
D
im
en
si
on
s
W
a
r
r
a
n
ty
▲
▼ … S e l e c t d a t a .
SET
… Make the set data
effective .
1 2 1 2 1 2 1 2 :::: O f f s e t M o d e O f f s e t M o d e O f f s e t M o d e O f f s e t M o d e
( 2 ) X 1 ( 2 ) X 1 ( 2 ) X 1 ( 2 ) X 1
▲
▼
… S e l e c t d a t a .
SET
… Make the set data
effective .