Tsubaki LINIPOWER Скачать руководство пользователя страница 10

Страница: 10 / 37

6. Trouble shooting

Most of jack troubles arise from improper lubrication, inappropriate selection, and misalignment. Please use the
following trouble shooting table when investigating problems.

Table 6. Trouble shooting

Trouble

Cause

Action

Gear Housing

Failure

1. Over load

2. Improper support

3. Shock

・

Reduce the load or replace with a unit of sufficient capacity.

・

Install the jack to a robust base and align proplerly.

・

Provide a shock absorbing device.

Input

Shaft

Failure

1. Improper centering

2. Excessive overhung load

3. Overload

4. Impact load

5. Excessive input

・

Tube coupling may cause shaft failure. Please use flexible

coupling.

・

Re-align as mentioned in installation page.

・

Check the catalog for allowable loads and adjust.

・

See Gear Housing Failure #1.

・

Provide a safety device to avoid possible impact loads.

・

Set the input power to be less than the allowable input torque

in the catalog or replace it with a larger unit.

・

When several jacks are connected in series, there is a

limitation on the input shaft of the first jack due to the axia

strength. If the current value exceeds the catalog value, reduce

the load or change the jack to one with a larger capacity

Bearing

Failure

1. Overload

2. Excessive overhung load

3. Coupling misalignment

4. Coupling axial adjustment

5. Abnormal force to

worm wheel bearings

6. Improper lubrication

7. Impact load

・

See Gear Case Housing #1.

・

See Input Shaft Failure #2.

・

See Input Shaft Failure #1.

・

Although the specified pressure has been applied to the

bearing, the input shaft can be rotated freely when no load is

connected. If the rotation is heavy, some force may be

applied to the input shaft in the axial direction. Remove the

force.

・

See #5 (Maintenance and inspection) of this manual.

・

See Input Shaft Failure #4.

Abnormal wear of

travel nut/

worm wheel

1. overload

2. Improper lubrication

3. Improper

adjustment/installation

・

See Gear Housing Failure #1.

・

See Bearing Failure #6.

・

Set the load so that it will be applied onto the same axis as the

screw shaft.

Ball nut damage,

abnormal wear

1. Overload

2. Improper

adjustment/installation

3. Improper lubrication

4. Inappropriate sizing

・

See Gear Housing Failure #1.

・

Set the load so that it will be applied onto the same axis as the

screw shaft.

・

See Bearing Failure #6.

・

Check the catalog for relationship between life and load.

Shaft failure,

Abnormal abration,

abnormal noise

1. Overload

2. Improper

adjustment/installation

3. Side load

4. Improper lubrication

・

See Gear Housing Failure #1.

・

See Ball Nut Failure #2.

・

Provide a guide to avoid side loads

・

See Bearing Failure #6.

Gear Housing

overheat

(over 80

℃

)

1. Overload

2. Improper lubrication

3. Improper centering

・

See Gear Housing Failure #1.

・

See Bearing Failure #6.

・

See Input Shaft Failure #1.

・

See Shaft Failure #3.

Содержание LINIPOWER




































Результаты поиска

Содержание LINIPOWER

Отзывы:

Tsubaki LINIPOWER, Инструкция по эксплуатации, Страница: 10 / 37

Результаты поиска

Содержание LINIPOWER

Отзывы: