TSPROF K03, Руководство пользователя, Страница: 10 / 15

1
Body K03 - 1 pc.
2 Abrasive holder - 1 pc.
3
Stand - 1 pc.
4
Wholemilled clamp - 2 pcs.
5
Double clamp - 2 pcs.
6
Single clamp - 1 pc.
7
Single fillet clamp - 1 pc.
8
Smal universal table - 1 pc.
9
C-Clamp - 1 pc.
10
Spare Parts kit – 1 kit
17 18
*illustrations do not include accessories
and abrasive stones
10. Spare parts kit :
A
Allen wrench, L-shaped, 2mm - 1 pc.
B
Allen wrench, L-shaped, 2mm - 1 pc.
C
Allen wrench, L-shaped 3mm - 1 pc.
D
Clamp ca libration plates - 2 pcs.
E
Felt pads - 2 pcs.
F
Clear rubber bu mpers - 5 pcs.
G
Screw М4х16 – 3 pcs .
I
Screw M3 x 12 - 4 pcs.
3. SAFETY REQUIREMENTS
ATTENTION!
Before using the sharpening system, please read this User Manual carefully. Incorrect handling
of this product could result personal injury or physical damage. The manufacturer assumes no
responsibility for any damage or injury.
When using the base, keep the system at a safe distance from the edge of the work-surface.
The system is heavy and cause injury if it falls from even a small height.
When using a C-clamp to secure the body of the sharpening system to a work-surface, make sure
that the C-clamp is firmly tightened, and the body is securely retained.
Before starting the sharpening process, be sure to install and correctly adjust the bar
limiters (page 22).
It's recommended to wear cut-resistant gloves during blade clamping, adjusting,
and during sharpening.
Cut-resistant gloves are widely and inexpensively available from TSPROF, or many other suppliers.
During sharpening, beware of accidental rotation of the pivot-arm. This can happen if a pivot-arm
tension is adjusted too low, or excessive pressure is applied to the abrasive stone.
Properly adjust pivot-arm tension (page 20).
Do not leave a blade, clamped in the system unattended. Keep system out of reach
of children and pets.
MAINTENANCE TIPS
The machine internals are security sealed; if opened, the warranty is void.
To preserve appearance and prevent corrosion, periodically remove dust and dirt. Wipe system
with a cloth slightly dampened with household oil. Remove excess oil with a cloth afterwards.
Lubricate moving parts using a household oil.
Check system condition before each sharpening session. Make adjustments if necessary
(see Calibration, page 24).
Movements of the abrasive holder bar during sharpening should be smooth and even, without
any jerky motions or excessive pressure on the abrasive.
When sharpening is complete, brush off any loose debris from the system and carefully
clean all surfaces.
For transportation, disassemble system in the reverse order. To avoid damage, wrap carefully and
pack in an appropriate box or case. Do the same for long-term storage.
Store in a dark, dry place at room temperature. In a wet or humid climate, place several packs
of silica humidity absorbers inside the box or case, prior to storage, lubricate with household
oil all places where corrosion could occur.
Damage or excessive wear of threaded connections may appear after long use, especially at the
clamp adjusting spring. To prevent this, we recommend regular use of household oil, as well as
closely following the blade-clamping instructions. Replace clamp screws and springs periodically
or as-needed.
If any complex parts are worn or damaged, contact the manufacturer, TSPROF, for support.
Dispose of the system as household waste as appropriate.
1. TECHNICAL CHARACTERISTIC
2. COMPLETED UNITS
( depending on the kit ordered )
2.
1 2 3
4
5
6
7
8
9 10
I A B C D E F G
The TSPROF K0 3 is a universal sharpening system, designed for sharpening
both sides of a blade without re-clamping, for creating a symmetrical blade bevel,
correcting an unwanted blade, and general grinding and polishing of cutting tool edges.
Sharpening angles K03 Standart * 7° to 23°
Sharpening angles K 03 Expert * 7° to 35°
Overall System dimensions 250х220х330 mm
Weight of the K03 body abrasive holder 2,05 kg
Length of the assembled abrasive holder 710 mm
Length range of the abrasive stone 150 to 210 mm
Maximum sharpenable blade length 700 mm
Pivot-arm rotation angle 180° ± 0,2°
*
dependent on the clamping, blade type, and the stone type used