background image

xii 

Model 3076 Constant Output Atomizer 

 

Appendix B:  Technical Paper 

 

This appendix contains a technical paper on the Atomizer. 

 

 

Appendix C:  Bibliography 

 

This appendix contains a list of references used in writing this 
manual. 

 
 
 

R e l a t e d   P r o d u c t   L i t e r a t u r e  

 

Model 3074B Filtered Air Supply 

(part number 1933800) TSI 

Incorporated 

 

This manual contains setup and operating instructions for a 
filtered air supply, which can be used with the Model 3076 
Constant Output Atomizer. 

 

 

Model 3012/3012A Aerosol Neutralizers 

(part number 

1933012) TSI Incorporated 

 

This manual contains specifications and installation instructions 
for the Model 3012 and Model 3012A Neutralizers, which can be 
used with the Model 3076 Atomizer to neutralize charged 
particles. 

 

 

Model 3077/3077A Aerosol Neutralizers 

(part number 

1933077) TSI Incorporated 

 

This manual contains specifications and installation instructions 
for the Model 3077 and Model 3077A Neutralizers, which can be 
used with the Model 3076 Atomizer to neutralize charged 
particles. 

 
 
 

R e u s i n g   a n d   R e c y c l i n g  

 

As part of TSI Incorporated’s effort to have a minimal negative 
impact on the communities in which its products are manufactured 
and used: 

  This manual uses recyclable paper. 

  This manual has been shipped, along with the instrument, in a 

reusable carton. 

 

Содержание 3076
































































Отзывы: