TSC TTP-2410M Pro Скачать руководство пользователя страница 2

Страница: 2 / 54

TTP-244M Pro/244ME Pro
TTP-342M Pro/342ME Pro

Bar Code Printer Service Manua

TABLE OF CONTENT

FUNDAMENTAL OF THE SYSTEM ........................................................................... 3

1.1. Features of TTP-244M Pro/TTP-244ME Pro/TTP-342M Pro/342ME Pro ............. 3

1.2

Model Naming Rules ...................................................................................... 3

1.3

Overview ......................................................................................................... 4

1.4 Basic Specifications ....................................................................................... 7

1.4-2

Electronics/Communication Specifications ................................................ 8

1.5

Available Bar Codes ...................................................................................... 9

1.6

Various Sensors and Switches ................................................................... 10

2. SUPPLY SPECIFICATIONS ..................................................................................... 12

2.1 Types of Paper .............................................................................................. 12

2.2

Paper Specifications .................................................................................... 12

2.3

Ribbon Sizes and Shapes ........................................................................... 13

3. ELECTRONICS ........................................................................................................ 15

3.1 Summary of Board Connectors .................................................................. 15

3.2 Interface Pin Configuration ......................................................................... 18

3.3 Replacement of Main Board ........................................................................ 20

3.4

Print Density Selection ................................................................................ 22

3.5 Replacement of the LCD Display ................................................................ 23

3.6 Replacement of the Keypad Board ............................................................. 24

MECHANISM............................................................................................................ 25

4.1

Cutter Installation (Option) .......................................................................... 25

4.2

The peel-off module sensor installation (Option) ...................................... 28

4.3 Replacement of Printhead ........................................................................... 30

4.3-1

Replacement of Printhead (For ROHM) ...................................................... 30

4.3-2

Replacement of Printhead (For KYOCERA ) .............................................. 31

4.4

DC Motor Replacement ................................................................................ 33

4.5 Replacement of Stepping Motor ................................................................. 35

4.6 Installation of Black Mark Sensor ............................................................... 37

4.7 Replacement of Ribbon Sensor (Receiver) ................................................ 39

4.8 Replacement of Ribbon Sensor / Gap Sensor (Transmitter) .................... 41

4.9

Platen Replacement ..................................................................................... 42

4.10 Replacement of the power supply .............................................................. 44

Содержание TTP-2410M Pro























































Результаты поиска

Содержание TTP-2410M Pro

Отзывы:

Похожие инструкции для TTP-2410M Pro

Бренды по названию

Популярные бренды

TSC TTP-2410M Pro, Руководство по обслуживанию

Результаты поиска

Содержание TTP-2410M Pro

Отзывы:

Похожие инструкции для TTP-2410M Pro

Бренды по названию

Популярные бренды