TSC TE200 series Скачать руководство пользователя страница 5

Страница: 5 / 48

TE200/TE210/TE300/TE310 Series
Bar Code Printer Service Manua

1.3 Rear View

Power switch

Power jack socket

USB interface (USB 2.0/Full speed mode)

USB host (TE210/TE310 Series only)

RS-232 interface (TE210/TE310 Series only)

Ethernet interface (TE210/TE310 Series only)

Note:

The interface picture here is for reference only. Please refer to the product specification for

the interfaces availability.

* Recommended SD card specification.

SD card spec

SD card capacity

Approved SD card manufacturer

V1.0, V1.1

microSD 128 MB

Transcend, Panasonic

V1.0, V1.1

microSD 256 MB

Transcend, Panasonic

V1.0, V1.1

microSD 512 MB

Panasonic

V1.0, V1.1

microSD 1 GB

Transcend, Panasonic

V2.0 SDHC CLASS 4

microSD 4 GB

Panasonic

V2.0 SDHC CLASS 6

microSD 4 GB

Transcend

- The DOS FAT file system is supported for the SD card.

- Folders/files stored in the SD card should be in the 8.3 filename format

Содержание TE200 series

















































Результаты поиска

Содержание TE200 series

Отзывы:

Похожие инструкции для TE200 series

Бренды по названию

Популярные бренды

TSC TE200 series, Руководство по обслуживанию

Результаты поиска

Содержание TE200 series

Отзывы:

Похожие инструкции для TE200 series

Бренды по названию

Популярные бренды